Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:3670737.

I really like the 6" Rack that KronBjorn designed, and I have four Raspberry Pi's in my rack, so I needed a way to power them.

I have the Anker PowerPort 6 for this purpose, I just needed a way to mount it.

I remixed the Raspberry Pi 3 case by KronBjorn. It is not a perfect way to mount the PowerPort, as it can move up and down in the case, but with one USB cable attached, it stays in place.

If it isn't clear from the pictures, the USB ports are in the back of the rack, so there are no cables in the front.

The case is 3U tall.

6" Rack, Anker PowerPort 6 power supply

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:3674711.

I really like the 6" Rack that KronBjorn designed, and I have four Raspberry Pi's in my rack, so I needed a way to connect them with network.

My switch is a TP-Link TL-SG105, I just needed a way to mount it.

I remixed the Raspberry Pi 3 case by KronBjorn. The switch is locked in place, when the case is screwed together.

If it isn't clear from the pictures, the RJ45 ports are in the back of the rack, so there are no cables in the front.

The case is 3U tall.

 6" Rack, TP-Link TL-SG105

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4048093.

I have a Philips Ecomoods Suspension light (40339), in which the fluorescent tube died the other day.

When I took the lamp apart, I found out that the two clips that hold hold the tube in place had become yellow and brittle to the point, where it snapped.

While waiting for Postman Pat to show up with a new tube, I designed a replacement part.

Philips Ecomoods Suspension light clip

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4548039.

After COVID-19 hit the world, I started having a small bottle of hand sanitizer in my car.
Between the two cup holders there is a small spot that is the perfect for a bottle, but it was slipping around, if I didn't have two cups or bottles in the car.
This small holder keeps the bottle in place, even in the fastest corners.. :-)

Its designed to fit the cup holder in the Ford Fiesta MK7 (MK8 in the UK). 
My hand sanitizer is a small bottle of "Assured" Hand Sanitizer from Dollar Tree - usually two or three bottles for a dollar.

Ford Fiesta MK7 Hand Sanitizer holder

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4734278.

I ran out of power plugs under my desk, so I designed a bracket that could hold two strips.

The power strip I used is 50mm wide and 40mm tall.

Dual power strip mount

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:3519568.

I was building a small Raspberry Pi Cluster, and printed the "Raspberry Pi Rack case or rack cluster" by yooodaha. Then I saw hubschrauber's stand for the Netgear GS108. I liked the design, but I already had a TP-Link switch in a drawer, so I made a similar design in OpenSCAD.

I used a M5 threaded rod in the Raspberry Pi Rack, going through all four pillars, and on the top and bottom I have a regular M5 nut. My cut of the M5 had a few sharp edges, so I printed some nut caps, which then fits into the TP-Link stand.

Edit: 
Added a version, with longer legs.

Regular version goes from top of the switch to the bottom of the metal case.
"Higher_feet"-version goes a bit further, and includes the length of the rubber feet on the switch.

Raspberry Pi Rack - TP-Link TL-SG105 stand

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:3583636.

The original rubber feet broke on my IKEA Dagotto. 
I printed the model designed by Axl_K, but on a hardwood floor it slid around.

I recreated the design in OpenSCAD, and made the bottom part hollow, so I could insert a piece of rubber granulate mat.

It's designed for a rubber mat that is 1 cm tall, but I attached the OpenSCAD file, so it is easy to change - just one variable.



IKEA Dagotto non-slip stand 

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:2407143.

The settings knob on my Rowenta DW4005 steam iron broke off, and I made a new one in Sketchup. Use it if you can.

Rowenta Autosteam Iron RW4005 spare part

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4227293.

I needed more power sockets under my desk, so I bought a power strip which had some very poor mounting options.

So I designed a simple bracket.
I don't expect many people to use this model, as it isn't very well designed and the power strips in Denmark isn't like any other countries. .However, I wanted to share it as inspiration for others. 

Power Strip Mount

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4734284.

I bought a watch case opening tool from China, but the case it came it was horrible. All the attachments fall out all the time, so I designed a new case in Tinkercad.

The case closes with 5x5mm magnets.

Watch opening tool case

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:2187956.

I wanted to mount a USB hub under my desk, and I couldn't find one that supported mounting for a fair price. So I bought the i-tec 7 port USB 3.0 Metal Charging Hub (P/N: U3HUB778) and designed a mount for it.

You need to print two of these, and one should be a mirror of the other. 


i-tec USB 3.0 Metal Charging Hub mount

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4638529.

I needed a stand for a laptop at work, so I created a simple verson in OpenSCAD.
There are two version, one for laptops that are 18mm thick, and one for 22mm thick laptops.

The OpenSCAD file is attached as well, so it's simple to create another size.


Simple laptop stand

Activity related to collaborating with others on models

Likes, comments, and activity from your community

A roundup of models that we think you'll like

For when we think someone might have posted your content as their own

New content from your premium memberships

Emails and messages from designers you follow

GiuseppinaMoltisanti

Achievements

Seedling

Explorer