Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4636113.

Small stand for something, put a smile on it as looked like a nose. 4cm height,  5cm base diameter. Two files with 1cm and 2cm diameter tops. 

Smile Stand

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4650279.

Rear facing headphone hanger for MSI OPtix MAG271CQR. The build in hanger goes out to the left and I need it going out to the rear, this adapter will clip on to the existing hanger and when pushed in should lock in place. 

The insert in to the monitor is thin, if you're concerned about it breaking inside the monitor then remove it for slightly a less sturdy mount. 

This wont easily come off once you've clipped it on, safer to cut it off.

Rear Headphone Hanger for MSI Optix Monitor

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4699302.

A 4mm internal diameter nozzle narrower than the 8mm one that came with the air duster. Using it with an ATEnge duster but I think these are generic devices with lots of different brand names. About the same length as the original. 

ATEnge Air Duster Nozzle 4mm

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:5260424.

2D print of one of the Burghead Bulls Pictish stone carvings from the 7th century.  

Burghead Bull

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4681955.

Belt buckle cover for costume, 12x5cm for a belt up to 3cm tall. Plain cover and a cover with ELF.

Belt Buckle Cover - Plain and ELF

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4859480.

Wall mount for a TP-LINK SG1008p network switch allowing it to be slid in and out from the top. Switch will need the sticky feet removed to face the other way from the picture. 

Needs supports.

TP-LINK TP SG1008 Wall Mount

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4567546.

A replacement key head for ABS Avocet keys, bit rough but it works. I've had four of the original key heads break in the same way so needed some replacements.

It's a one piece build and will require a pause set in the slicer to insert the key shaft before resuming printing over the top of it. Having something about 1.75mm tall for the front of the key to sit on while inserting and after the printing resumes would be a good idea.

There's a bit of variation in the shafts but it fit all of them well enough. 

ABS Avocet Key Head

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4562329.

Just something to stick where the QR code is on the Ender 3, Yar from my favorite Atari 2600 game Yars' Revenge. The Qotile for the other side if wanted has holes to push fit at the end of my rail, might not fit depending on the alignment.

Printed with a filament change having the base black and the top layers in colour to stand out. 

Enders' Revenge

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4651098.

A mouse bungee secured to the right leg of my MSI Optix MAG271CQR monitor. Should be fine with up to a 3mm cable. 

MSI Optix Mouse Bungee

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4647089.

A 4cm riser for an older dell monitor, I have a pair of the monitors and needed them raised a but while having some room for cables to pass under. Seems sturdy enough for my use and fits in to the 4 holes in the base. 

Two 4cm boxes might have done but any excuse to make something.

Dell Monitor Stand Riser

Activity related to collaborating with others on models

Likes, comments, and activity from your community

A roundup of models that we think you'll like

For when we think someone might have posted your content as their own

New content from your premium memberships

Emails and messages from designers you follow

Funky Dysfunc

Achievements

Seedling