Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:2774313.

Remixed just to add 3D Printable rings for the eyes so you don't have to paint them. I glued them on with hot glue, but better glue should be used.

This model was used in Xander's Thing Thursday Episode 23
https://youtu.be/nMVyo7Yswas

All credit the the original designer and the first remixer.

Poop Emoji Trophy With Eye Rings

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:3639244.

This is a remix of the Lego_man. Holder toilet paper by vvK187.

We buy the extra large rolls of Quilted Northern (https://amzn.to/2VBXz7r) and they just would not fit on this. I scaled him to be a little bigger, then I carved out the torso a little and now the rolls fit perfectly.

I have printed this 4 times all with perfect success.

The hands should be rotated to lay flat on the bed.

Supports for the head and roll axis.


Lego MiniFigure Toilet Paper Holder For Larger Rolls

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:2819503.

EDIT: Version 3.1 has replaced the original. This is a better design with 2 points for the zip ties which stop it from wiggling. 

This is an add-on for the Anet E12 to support the heat bed cable. It removes the stress of the cable moving around from connector. This unit screws on to the where the bearing block is mounted. It should be noted that I used longer screws for this (M4x12) as it did not feel like the factory screws grabbed enough threads.

This was designed with a slot for a 4" zip tie to go through on the end and secure the cable.

I also made it go off at a 45 degree angle to keep the cable away from the Y limit switch.

NOTE: When I sliced this in Slic3r PE, it sliced it with the rib that runs the length on top of a solid layer. This delaminated on me when I flexed it. Cura printed it open and it seems better. So your mileage may vary.

Anet E12 Heat Bed Cable Holder (Support)

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4707376.

These bins fit the steel dividers in the top drawer of the Harbor Freight Vulcan welding cabinet number 63179

https://www.harborfreight.com/heavy-duty-large-welding-cabinet-63179.html

The divider is not fixed to the drawer and I did not want my consumables to get mixed, so I made these simple little bins.

I have made a video about them here: https://youtu.be/wW1iA5S_iJE

Harbor Freight Welding Cabinet Drawer Bins 63179

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:3127646.

This is a set of tools that will allow you drill for blind fastening and tap the ends of V Slot aluminum (Aluminium) such as that from openbuilds.com. 

I needed these while building my FK-1 large format 3D Printer. (https://www.youtube.com/playlist?list=PLoJycTgmGC47H5_A7Fs0giDvwOR5HQZRE)

The bushings I used for these are from Amazon and are available here:
https://www.amazon.com/gp/product/B01G8XA51G/ref=as_li_ss_tl?ie=UTF8&psc=1&linkCode=sl1&tag=funking3d09-20&linkId=d94572c17b24b33c8dbe83ded11efe9e&language=en_US (affiliate link)
*Note: These should be about $4.50 USD. If they are higher, you might have to wait and let them come back down. I have seen them jump up to $14 USD.

A quick how-to and example video is available here:
https://youtu.be/-Mqe7MNBpcA



V Slot Drilling and Taping Jigs

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:2395388.

I know there are others out there, but I ran into an issue where the other one I printed was too large and hit the front of the frame. These are pretty much the size of the wing nut (A little taller due to the bottom layer.)

These work well with or without the drilling of the H frame. I found the rear wing nuts difficult to reach at times during leveling. These help a great deal.

They fit the factory wing nuts very tight. I pushed them in with a screw driver and seated them the remaining amount by threading them on.

These were printed in Hatchbox PLA.

Thanks for checking it out. We are open to all input and comments. 

As always, Print On!

Anet A8 Bed Leveling Knob

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:3296274.

This is a fun little snowman designed in TinkerCad by Xander. He felt it needed a mustache and so it was!

The photo showing the printed model was at 200%

This is featured on a Xander's Thing Thursday here: https://youtu.be/UuP13UVNNIQ

The Snowman With A Mustache

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:2441064.

These little guys cover up your unused USB ports to keep dust and junk out of them. Are they needed? No. But they look great with my Pi case. (https://www.thingiverse.com/thing:2391969)

I just wanted to cover up the unused ports on my Octopi setup. I have one for each printer so I only use one port (two with a camera.) This covers the other. There is one that covers 2 ports and one that is single. (You can use two singles to cover a double. They stack.)

Will these fit other devices? The single one will, the double one.. well your mileage may vary on that. It seems that most double USB stacks are close to the same size, but not all are.

I will upload actual photos at some point. I have these installed currently.

Raspberry Pi USB Port Cover

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:2556020.

This is a rocket that Xander designed in Tinker Cad.

Powerful Atlas Sky Rocket

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:2397726.

This is a cover for the extruder fan. I replaced the stock 40mm fan with a Noctua 40mm fan for noise reduction. (It works wonders!) The problem is that the Noctua fans are a weird brown color and that does not work with my OCD. So I created this little cover to put over the fan.

Fits very nice and has a relief for the wires to come out on left (back of printer) toward the top.

As with everything that Fun King 3D designs, we are open to comments and change requests. We hope that the items we offer help you in some way.

And as always, Print On!

Anet A8 Extruder Fan Cover

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:2810113.

This is a robot designed by 11 year old Xander from Fun King 3D. This robot was designed in tinkercad and is an easy print.

Gearbot

Activity related to collaborating with others on models

Likes, comments, and activity from your community

A roundup of models that we think you'll like

For when we think someone might have posted your content as their own

New content from your premium memberships

Emails and messages from designers you follow

FunKing3D

Achievements

Seedling

Debutant