I printed two and I really love them! For my 12s anyway I had to scale it a bit, but getting the guitar is no smooth as I would like. Could you share a modified version of the object as in my photo? I am able to cut it but I am not in a cool way. Thanks.
It really didn't shrink too much for the uke. Turns out the head was about the same size as the guitar, the neck was skinnier though. Maybe 10 mm difference.
Something is not alright with the pushing mechanism. It’s stuck and not releasing properly. I saw a lot of comments with the same problem . Print is fine, assembly pretty easy and I don’t think that’s the issue. Any help of how to fix this ?
Have you inspected the parts that are sticking to see if there are any signs of overextrusion or warping? We've seen that even a slight bump or warp in the part can cause the sticking. You can also try adding vaseline to the print to get it to unlock itself easier.
Love the looks of it but can't seem to get it to work. Printed on P1S using Bambu matte green with a .4 nozzle. I put in vaseline and it's still hard to get it to close. When I push down on the parts where the guitar goes it needs force. One side slips down over the gear and gets stuck down. When I push them inwards and then push down it works good but that doesn't happen when the guitar gets put on. Any help would be great! Thanks.
Hi, It sounds like you may have it either assembled slightly off, or you could have some print quality issue that is making the tolerences in the grears too small. I would Double check assembly and rewatch my assembly video to ensure everything is lined up right. Next I would double check that your nozzle is clean and not worn down causing overextrusion.
Hello, just bought a subscription to print this model! I printed in Pla - .2 layer height. Everything fits together nicely but I experience some crunching and locking up. I gave all the moving parts (that I could reach) I good sand and now the locking has stopped but gears do not feel very smooth and require some force to move. New to 3D printing so could be a user error. Would you recommend printing somewhere closer to .15? Will go buy some Vaseline to try tomorrow. Thank you
If you want to use that slicer, please open the STL files. But i highly recommended switching to a slicer like Bambu Lab that will open the 3mf perfectly!
Hello! I have an Ender 3 S1 and just finished printing this (0.2mm layers) All the pieces were orientated upright like image 4 above. After printing, I tried to slot the levers into the base, but the hole in the base seems too small for the levers. I used a small knife to make sure the holes on the base were clean but the levers are still too tight for the hole. Anyone else have this problem? Is it just an issue with the holes maybe not being shaped right because of not using supports?
so i printed it did not scale or anything. turned out really with my Bambu p1s but when to check it before hanging on the wall and discovered that the neck of the 2 guitars we have are just too wide. the one is a normal guitar but the other is a kid size one. so I'm a little confused. it fits if i put angle it in but if i mount it to the wall then i would not be able to angle it enough to get it in. i used the 3mf file
Discussions — Auto Locking Guitar Holder
How much did you scale it down to fit your ukulele?
It really didn't shrink too much for the uke. Turns out the head was about the same size as the guitar, the neck was skinnier though. Maybe 10 mm difference.
W here are the assembly directions?
You can find them Here
Something is not alright with the pushing mechanism. It’s stuck and not releasing properly. I saw a lot of comments with the same problem . Print is fine, assembly pretty easy and I don’t think that’s the issue. Any help of how to fix this ?
Have you inspected the parts that are sticking to see if there are any signs of overextrusion or warping? We've seen that even a slight bump or warp in the part can cause the sticking. You can also try adding vaseline to the print to get it to unlock itself easier.
Love the looks of it but can't seem to get it to work. Printed on P1S using Bambu matte green with a .4 nozzle. I put in vaseline and it's still hard to get it to close. When I push down on the parts where the guitar goes it needs force. One side slips down over the gear and gets stuck down. When I push them inwards and then push down it works good but that doesn't happen when the guitar gets put on. Any help would be great! Thanks.
Hi, It sounds like you may have it either assembled slightly off, or you could have some print quality issue that is making the tolerences in the grears too small. I would Double check assembly and rewatch my assembly video to ensure everything is lined up right. Next I would double check that your nozzle is clean and not worn down causing overextrusion.
Hello, just bought a subscription to print this model! I printed in Pla - .2 layer height. Everything fits together nicely but I experience some crunching and locking up. I gave all the moving parts (that I could reach) I good sand and now the locking has stopped but gears do not feel very smooth and require some force to move. New to 3D printing so could be a user error. Would you recommend printing somewhere closer to .15? Will go buy some Vaseline to try tomorrow. Thank you
Vaseline!! Makes it move very smoothly
Hello, Simplify3D fails to parse the 3mf file!?
If you want to use that slicer, please open the STL files. But i highly recommended switching to a slicer like Bambu Lab that will open the 3mf perfectly!
Switch to Arachne slicer. Make minimum feature size 1%
Hello! I have an Ender 3 S1 and just finished printing this (0.2mm layers) All the pieces were orientated upright like image 4 above. After printing, I tried to slot the levers into the base, but the hole in the base seems too small for the levers. I used a small knife to make sure the holes on the base were clean but the levers are still too tight for the hole. Anyone else have this problem? Is it just an issue with the holes maybe not being shaped right because of not using supports?
Yeah sounds like maybe your printer didnt do the overhangs of the holes quite right. Try using supports and you should have better luck
so i printed it did not scale or anything. turned out really with my Bambu p1s but when to check it before hanging on the wall and discovered that the neck of the 2 guitars we have are just too wide. the one is a normal guitar but the other is a kid size one. so I'm a little confused. it fits if i put angle it in but if i mount it to the wall then i would not be able to angle it enough to get it in. i used the 3mf file
Its designed so you turn the guitar just slightly to fit, which helps it be more secure!
i love the filament colors of all of your prints, especially all the different green tones. Could you upload a list of all the filament you use?
The filament is linked in the description!
Hey - I am having trouble downloading the files, i get the message "Download is not currently available"
Did that issue get resolves for you?
No, it still has this message
How about now? I have gotten confirmation from Thangs that this bug should be fixed
Hi excellent print, but what screw size and length is needed for the walls?
Standard Drywall screws. its designed to accept a lot of different screw types though