Parts to help you install MGN12H linear rails on the Y axis of your Sidewinder X2. Use the hold jig to assist in drilling the required mounting holes on the carriage plate for the bearing blocks. Use the Rail Jig, 3 of them, to align and space the rails on the 2060 Y axis aluminum profile. Use the Belt mount to hold the belt at the correct offset, no need to change belt motor or tensioner location. And use the end stop spacer under the end stop. This will require M5 and M3 hardware along with Tee Slot Nuts.  

Sidewinder X2 Y axis MGN12H Linear Rail Install Kit

Hole Jig Full.STL

Custom designed part cooling duct that fits a single 5015 blower fan. You can use this in conjunction with a BL-Touch or CR-Touch using my custom mounting bracket for ether probe. NOTE: will not fit with factory ABL probe.

EP3D SWX2 & Genius Pro 5015Part Cooling Duct V2.0.STL

Simple bracket to hold Bowden tube on a TwoTrees SP-5 for feeding into a direct drive extrusion system. Use a Bowden coupler with 1/8" NPT thread, M4x8mm socket head cap screws and tee-nuts.

SP5 Filament Guide Bracket..STL

Mounting Brackets to install a CAMXTOOL 10x11 Drag Chain on your TwoTrees SP-5

Drag Chan Mounting Brackets for TwoTrees SP-5

Carrage Mount.STL

Mounting Brackets to install an E3D Hemera Revo or Revo XS with dual 5015 fans on your TwoTrees SP5 or SP3.  It supports both a mounting location for a GL-8H inductive sensor for use as an auto leveling probe. And a mount for a BL-Touch. For the inductive porbe use offsets { 0, 43.04, -0.85 }, For the BL-Touch, use probe offsets { 0, 43.85, -1 }

TwoTrees SP5 and SP3 Hemera Revo mounting bracktes

Front Mount & Fan Shroud V2.STL

Rear Mount & Fan Shroud V2 (BL-Touch).STL

Bowden Fitting.STL

BL-Touch Mount.STL

Easily replace your stock probe on your Sidewinder X2 or Genius Pro with a BL-Touch, CR-Touch or 3D-Touch using this mount. Use M3 screws to mount. The nozzle to probe offset is close to stock so you can get by without updating the firmware with the new values but for maximum accuracy I suggest changing the values in the firmware.

Sidewinder X2 and Genius Pro BL-Touch-CR-Touch Mount

V1 Dual 5015 part cooling fan duct for Sidewinder X2 and Genius Pro

SWX2-GPRO Dual 5015 Cooling Duct.stl

BTT case that fits Artillery 3D printers other than the Hornet

TFT 35 Artillery Case.stl

Part cooling fan duct for a 5020 fan for both Sidewinder and Genius 3D printers.

Sidewinder and Genius 5020 Part_Cooling_Duct.stl

Sidewinder and Genius 5020 Part_Cooling_Duct SPLIT.stl

Beta version of a mount for a Hemera XS on Sidewinder and Genius 3D printers.

Sidewinder and Genius Hemera REVO XS Adaptor Plate.STL

Sidewinder and Genius Hemera XS Adaptor Plate REVO, V6 & Volcano.STL

Break Oout Board Spacer.STL

5015 Part cooling fan duct for the E3d Hemera. Fits REVO, V6 and Volcano hot ends.

Hemera 5015 Part Cooling Fan Duct Rev 8.2.stl

Simple adaptor plate to mount an E3D Hemera to both Sidewinder and Genius 3D printers. Works with REVO, V6 and Volcano hot ends. BL Touch mount is stealthily hidden behind the extruder assembly and probes very close to the nozzle. Plenty of space to fit your cooling fan duct of choice. You can also download my cooling fan duct as well.

Sidewinder and Genius Hemera mounting plate  V6 & Volcano.stl

My BL Touch mount for the Sidewinder X1 with larger mounting holes to fit machines with extruders that have the standoffs screwed to the stepper motor. Use these offsets;
X 31, Y -17.6, Z -2.5

SWX1 BL Touch Mount.STL

SWX1 BL Touch Mount (Big Holes).STL

BL Touch Mount (Small Holes).STL

Simple brackets to increase the rigidity of the Z axis to reduce z wobble. Use M3x12mm socket head cap screws with washers to mount to the stepper motors.

Sidewinder X2 Gantry Supports

Simple way to angle the outlet water flow in your Intex pool to properly circulate the water. Use M5 sockethead cap screws 10 to 15mm in length. 

Intex Pool Outlet-Adjustable

Pool Outlet Cover.STL

Side mounted spool holder and upper filament guide, can be mounted on the left or right side of the machine to fit your workspace.

Sidewinder X1 Spool Holder and Guide

Spool Holder.STL

Front grill for those that want to enclose the bottom of their TronXY X5SA 3D printer 

TronXY X5SA Grill

Hood Ordament.STL

A remix of my preferred fan duct to fit a 5015 fan. This will clear the leveling probe on the Sidewinder X2.

Artillery Sidewinder X1 and X2 5015 part cooling fan duct.

SWX1-2_5015_PART_COOLING_FAN_DUCT.STL

This is my own design of a fan duct for a 5015 fan to fit on a Hemera with a V6 hot end. This is still in the developmental phase and still requires testing. 

5015 Fan Duct for Hemera V6

5015 Fan Duct V5.0.STL

This is my BL-Touch mount with small mounting holes for machines that use long M3 screws to mount to the stepper motor. Use these offsets;
X 31, Y -17.6, Z -2.5

SWX1 BL-Touch Mount (Small Holes)

BL Touch Mount.STL

Activity related to collaborating with others on models

Likes, comments, and activity from your community

A roundup of models that we think you'll like

For when we think someone might have posted your content as their own

New content from your premium memberships

Emails and messages from designers you follow

Ethereal Project 3D