Fits mens US sizes 9.5-11.5ish?  This was definitely for the meme, so they work, but dont expect them to be comfy.

Parts to print in flexible filament: 
Main Shoe
Tongue
(Laces are just unused filament)

Parts to print in rigid filament:
Shaft Cap
Shaft
Shoe Base
Wheel

3D Printed Heelys

Main Shoe.stl

Moon Knight's Crescent Darts / Daggers.

Details show up best once resin printed and painted.  (Can definitely be printed FDM, just have only printed it in resin myself.)

Moon Knight Crescent Dart

Ronin sword from the Disney+ show Hawkeye.  
This sword has a hole through the middle for an 3/8inch rod. It does not go all the way through the sword since some of the holes in the blade interfere.

Full stl is provided as well as the 3 parts to the blade + the hilt.

Ronin Sword from Hawkeye

Full Sword.stl

Mandalorian helmet.

This is only the second thing I have modeled in Blender.  So I am definitely still learning!  

This model could be a lot cleaner for sure, but so far has printed without issues. 

Mandalorian Helmet

Mandalorian helmet.

My second attempt at modeling in blender. Still learning! :)

Loki's headpiece to go on your crocs.  

Honestly these were made just for the meme and not for comfort, but then people actually wanted it so here ya go.

Definitely would print in TPU or a flexible filament if you don't wanna stab your ankles.

THESE WERE MADE FOR THE MEME. I REPEAT. FOR THE MEME. (Which means they were derived from my previous Loki headpiece model in about 15 mins lol). If it’s a sucky model don’t hate me.

Loki Croc Attachment

Loki's headpiece to go on your crocs.  

Honestly these were made just for the meme and not for comfort, but then people actually wanted it so here ya go.

Definitely would print in TPU or a flexible filament if you don't wanna stab your ankles.

Loki's headpiece from the Disney+ show: Loki.

File is uploaded in two formats: one with the horns attached, and one with the horns separate.  

(My first model made in Blender... definitely still learning!)

Loki Headpiece

Loki Headpiece with Horns.stl

Used by Dr. Doofenshmirtz in The Phineas and Ferb movie:  Candace Against the Universe:

More information on Assembly will be available on my YouTube channel soon.

Trigger: Contains opening for limit switch, and area for wires to run out the back.  Contains indention for a spring to sit and push the trigger back in place. (Similar indention is on the Main Body.)

Knob:  Fits over a "uxcell 5 Pcs 10K OHM Linear Taper Rotary Potentiometer" installed from inside the back plate.

Back Plate: Fits a "HiLetgo  HD44780 1602 LCD Display Module" LCD screen and the potentiometer.  Entire Back plate is held on to the Main Body with magnets and slots (small circles indicate magnet placement.)

Main Body: The trigger hinges on the upper part of the handle.  Contains a platform for both an arduino and DF Player.  Contains area for speaker in the back.

Arms 1,2,3:  Ball and Socket joints.  Are hollow to run wires through.  Suggested to print 100% infill for strength, with no supports on the inside (hard to remove).  Heat up ball and socket joints with a heat gun and to loosen up joints to initially fit together if needed.

Chicken Beak: 3 LEDs can fit inside.

Chicken Replace-Inator

Chicken Replace-Inator.STL

Arc Reactor consisting of 6 different parts, held together by 3 identical pins (these can be printed & glued/melted on both ends).

Left room for LED's in both the "Clear Backlight Cover" and "Clear Ring," which should both be printed in clear plastic.

Iron Man Arc Reactor

Arc Reactor (Whole Assembly)

Here's the split version of the Captain America shield, with the added handle file:  

8 different Outer Ring Files, an Inner Circle, and a handle file that can be used for both sides.

Each handle mount file should work with straps ~ 1.5 inches in width.

Modeled to be comic accurate in size (meaning 2.5 feet in diameter). Scale to 86% for 26 inches in diameter (much more reasonable).

UPDATED Captain America Shield (With Handle)

WHOLE Cap America Shield With Handle Loops.STL

The shield from Falcon and the Winter Soldier!

UPDATED version is on my profile: 

Split into 9 different parts.
Includes handle mount file.

Captain America Shield (No Handle) FATWS.STL

The shield from Falcon and the Winter Soldier!

Captain America Shield FATWS.STL

Activity related to collaborating with others on models

Likes, comments, and activity from your community

A roundup of models that we think you'll like

For when we think someone might have posted your content as their own

New content from your premium memberships

Emails and messages from designers you follow

EmilyTheEngineer

Achievements

Seedling

Fan Favorite