Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4947999.

Remix of 3 models.

Takes the Brutus X Carriage, changes it so 2 of the screws screw through for better support. Slightly different front to take a 40 mm fan. And then twin blowers stuck on the side.

This is actually mounted on my Bonsai. Links to other things that went into this design.

Blower: https://www.thingiverse.com/thing:2274499
Frontplate: https://www.thingiverse.com/thing:3537449

Still takes a E3d V6

M3 Hardware:
3x16mm
2x40mm
2x22 mm
4xM3 Nuts


Dual Blower Bowden for Brutus X-Carriage

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4514645.


Taking a Huxley parts cooling fan from one design, and gluing a 40mm to blower fan converter on top from another design. Simple remix but does the job.

Huxley Surround Blower Parts Fan

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4514519.

The back plate is the unchanged from the Remix Source and can be downloaded from there.

The front part has additional section to fit a BLTouch and a zip tie to for cable management.

This gives me a probe off set of X -32, Y 15

This second version added 2mm on X offset so a wrap part fans can fit.

Huxley E3D Hotend with BLTouch

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4525084.


The original bracket and TFT case were exactly what I needed. I need a way to attach to my modified Huxley frame.

This item is just a clip to fix this to the Huxley, print the bracket and case from the original 'things'

Huxley BTT TFT3.5 Bracket Clip

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4545234.

A case for the BeebSID board, the board allows the C64 SID chip to be used on a BBC Micro. The case was designed around v2.4 of the BeebSID. Details are here

https://www.retro-kit.co.uk/page.cfm/content/BeebSID/
https://stardot.org.uk/forums/viewtopic.php?f=3&t=14803


Case for BeebSID

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4579806.


Remix of Electron MGC Case to create a case for the Acorn Electron GoSDC Cartridge.

Original MGC Case:
Dave Hitchins
https://stardot.org.uk/forums/viewtopic.php?f=3&t=18607

GoSDC Cartridge:
John  Kortink
http://www.zeridajh.org/hardware/gosdc/index.htm


Acorn Electron GoSDC Cartridge Case

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4549392.

Remix of Simon Inns BeebSCSI Right Angle (Horizontal) 3d Printed Case. The original case, PCB design and firmware can be found here.

https://github.com/simoninns/BeebSCSI

*'BeebSCSI is a Micro SD Card based SCSI storage emulation for the Acorn 8-bit range of microcomputers including the Acorn BBC Model B (with ADFS) and the BBC Master 128.'*

Case for BeebSCSI with vertical connector

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4896348.

Remix of Wolf Garten tool holder to fix to the official Wolf Garten tool rack.
https://www.thingiverse.com/thing:4811301

Came across the excellent tool holder for Wolf Garten tool system but wanted to add it to my existing tool rack, so I remixed it to fit.



Wolf Garten Tool Rail Holder

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4516861.

Might not be of use to anyone, but I upgraded my Huxley to a BTT SKR 1.4. I mounted it on 
https://www.thingiverse.com/thing:3692193

but I needed a lid and I am very limited on space (X,Y,Z), and all the cases I could find were too big. So I created the following.

The removable top was a bit of a fail as it does not give enough access to get at anything, so you still have to take the whole case off as all the connectors are around the edges.

Custom Huxley Case Lid for BTT SKR 1.4 

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4516893.

Photo is of first iteration which the clip was not quite strong enough on top and required a bit of glue, it was also a bit to close to the frame.

The STL model is version 2 (I haven't printed this version yet) that should fix these issues.

This is basically the original i3 mount with the Huxley Y carriage idler mount joined in the front. Does the job.

Huxley Webcam Mount

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4540983.

3d printed case for the FreeFi-232, a serial to wifi dongle for retro computers by Daniel Jameson.

To build one have a look here.

https://github.com/stardot/esp8266_modem


Case for FreeFi232 Wifi Modem

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4514563.


The original was exactly what I was after. I just had to take a chunk out of it so that is would fit the Huxley's Y Axis.

Huxley Y Axis Nema14 to Nema17

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4579830.

Shorter Laptop stand for Apple Macbooks (but fits others makes as well)

The original by *redwhite* looked great but didn't fit on my build plate (even though I have modded my plate from 140x140mm to 150x150mm), even putting it diagonally. So I twisted the end 90 degrees, to give the same area but allow it to fit, possibly more stable if you print one of each type i.e. left and right.

Angled Apple Laptop Stand

Activity related to collaborating with others on models

Likes, comments, and activity from your community

A roundup of models that we think you'll like

For when we think someone might have posted your content as their own

New content from your premium memberships

Emails and messages from designers you follow

Elminster