Apple Watch Charger Holder.stl

This is a holder they sell that worked great for the charger that comes with the Watch 6. Problem I had was the protective case pushed the watch up a few millimeters and wouldn't seat to be able to charge. Created a longer distance so problem solved.

Thin Rip jig v5.stl  #miterSlotWedge

5/16 Bar for your table saw or anything else you have with a miter slot. Use a 5/16" screw through you jig so it will wedge tight into the t-slot. 
Might want to print from a stronger material than PLA.
#woodworking #miter #slot

Thin Rip jig v4 5 point knob.stl #woodworking

5 point 5/16" knob for jigs #woodworking or anything else that needs a knob.

Push Stick.stl

22.5 Degrees Miter Sled v1.stl #woodworking 

22.5 Miter Sled v1.stl #woodworking 

lid_Bow_heart v8.stl

2020_extrusion_Clip v1.stl

Clip to hold wires in the middle of 2020 extrusion.

base_heart v5_small.stl

The base of the smaller heart version. Fits on Ender 3 bed.

lid_heart v4.small.stl

Lid_heart v3.stl #large

heart v2.stl #large

LCD_Plate_SKR_Enclosure_TFT35 v7.stl

LCD Cover for enclosure of SKR 1.4, Raspberry Pi 4, and a TFT35 lcd.

Top_SKR_Enclosure_TFT35 v6.stl

Top piece for enclosure of an SKR 1.4, Raspberry Pi 4, and a TFT35.

Bottom_SKR_Enclosure_TFT35 v5.stl

Bottom case of external SKR, Raspberry Pi, and TFT35 enclosure.

PSU Cover v5.stl

PSU Cover v4.stl #LRS-350-24 #Meanwell

This is the cover for the LRS-350-24volt Meanwell power supply. 115mm wide x 30mm deep.

SKR_Box v11.stl #SKR_V1.4

#SKR_V1.4 For the SKR v1.4 but fits the 1.3 and others. With the tab indentations from the lid.

SKR_Box v11 lid.stl

SKR_Box v8.stl

L-bracket v3.stl #2020ex

upperCornerKneeBrace v3.stl

Corner bracket for 2020 extrusion. This is for where the vertical and horizontal piece is not directly inline with each other. They are 20 mm offset from each other.

PSU Cover 360-12.stl

Power Supply for 3D printer. The s-360-12. This is a thicker style PSU. It is 50 mm thick.

SKR_Enclosure_TFT35 with tabs.stl

This is a better version of a stand alone box for a SKR 1.4 raspberry pi and a TFT screen. The previous versions I left the electronics in and I think they would be part of the print. This should be three separate pieces if not leave a comment and I'll upload them separate. #SKR #TFT35

hanging_soap_dish v1.stl

Have a corner shelf in my shower made of tile this is to hang another shelf where I can put the soap to drain.

phoneHolder v1.stl

Christmas tree v1.stl #gift

Gift Box v1.stl #gift

HappyNewYear_2021 version 2.stl

Top Hat Coaster HappyNewYear_2021 v1.stl #gift

RC_Car_Servo_Linkage.stl #redcat #everest

two hole corner brace small v2.stl

largeKneeBrace v1.stl

5 Point Knob 1/4 20 v1.stl

Sound Amp Phone v2.stl #gift

Handle Knurled Handle.stl

Dumpster_Fire_2020_v2.stl #gift

Dumpster_Fire_2020 v1.stl #gift 

Whistle v1.stl

Sliegh v1.stl #christmas #gift

yearPicFrame v2.stl #gift

Gnome v2.stl #gift

BabyYoda_2020 v2.stl #gift

docs.3dprint.help iMac, Fusion 360, Simplify 3D, Ender 3 Pro, Lulzbot AO 101.

Activity related to collaborating with others on models

Likes, comments, and activity from your community

New content from your premium memberships

Emails and messages from designers you follow

Get notified when someone purchases your models or memberships

Dumdumdev

Achievements

Seedling

Explorer

Up and Coming