Hey there, Thingiverse won't let me upload another version of my former design... So I decided to upload it here on Thangs.

I have opened the hole for the red cross laser and narrowed the air holes.

Twotrees Totem S Air Assist

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4838425.

I prolonged the design of genn by a bit so that it covers both sides.

You may need to apply some pressure on it with a rubber band so that it does not slip off... Or you warm up the plastic at the edges and bend it a little bit tighter ;)

Totem S Laser cover enlarged

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4461995.

The strap on my beloved skates just snapped. I did not want to throw them away because of this small issue. 
So i scanned the remaining strap and reconstructed it using FreeCAD and TinkerCAD. So far it works nice and is quite strong, but please let me know your experiences with this thing! :)

Inline skate strap - roller blade strap - FILA

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4693600.

Our vacuum cleaner robot ran up the feet of our IKEA Fejka Christmas tree and almost flipped everything over. Also, it got stuck once it drove up the ramp...
So I took one of the feet, scanned it, loaded it into Fusion 360 and designed a little bumper protection against not so smart vacuum robots.

It is meant to slide on easily from the front. Depending on your robot, you might need to glue it.

IKEA Fejka Christmas Tree - Vacuum robot feet protection

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4560737.

**I integrated TMC2208 V3.0 stepper drivers into my Anycubic Mega S.**

Make sure you have the mainboard with non-soldered stepper drivers!
I ordered **4 x TMC2208 V3.0 UART** version, please refer to the picture for pin usage. I use the stock firmware that is pre-installed on the printer.

1. Switch off and unplug your printer

2. Open the bottom of your printer

3. I changed X, Y and 2 x Z. The extruder can be left as it is, it's not that noisy.

4. Adjust the voltage, I used _~0.95 V_ on all drivers. Be careful not to cause a short-circuit, let someone help you if possible. _Something between 0.90-1.00 V_ will do. The adjustment screw is shown in the pictures below the blue heatsink.

5. Now the tricky part:
As I am not keen in programming and such stuff, I decided to do the hardware trick. 
As you can see in the pictures, **!! E0 AND Y !!** are in the original "wiring state".
All other cables need to be moved according to the pictures. In my case from top to bottom Black-Green-Red-Blue.

You can either pull out the brackets gently using pliers or you change the wiring in the connector. Manuals about that can be found online, it's not that hard...

Keep in mind that the _new drivers tend to get a bit warmer_ than the old ones. So you might want to cool them properly to avoid hardware damage or print failures.

_I use this thing to cool the drivers: https://www.thingiverse.com/thing:4280158_

When homing the axes for the first time, push them to their end stops before starting the motors. This is especially for Y. (Thanks to Exerptus for the reminder). Otherwise, the axis movement might behave strangely.

Aaaaand that's about it.

Switch on your printer and print one of those Benchy things or whatever you like and enjoy the silence :)


Anycubic Mega TMC2208 V3.0 UART

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4382766.

Customized version of https://www.thingiverse.com/thing:4159541

Created with Customizer! https://www.thingiverse.com/apps/customizer/run?thing_id=4159541



Cable clip 3 mm - Kleine Kabelklemme 3mm

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4943658.

I designed an air assist for the Twotrees Totem S from scratch in Fusion360.

It fits without any glue or screws. If you have any comments, let me know your experiences with it.
Oh, by the way: This thing blocks a part of the useless red cross laser... 

Use version 3 of this. I think it might work better (or make no difference at all lol).

Twotrees Totem S Air Assist, no glue, no screws

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4593987.

It didn't quite fit on the Dirtdevils' holder. I removed 0.3 mm on each side and 0.2 mm of the top.
I shortened it to 42 mm to fit the brush mount floor vacuum thing :)

1. Remove the broken holder with a plier
2. Remove the remains with a coarse file
3. Double-sided tape and zip-ties
4. Use a heat gun to soften the plastic of the holder on the vacuum itself
5. Insert and let cool
6. ???
7. Profit

Vacuum floor brush mount Dirtdevil M5080

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:5025397.

I stole DrNeis .stl and remixed it so that it fits on my 29 mm vacuum cleaner hose. Quick and dirty, but it works! :)

PSM 200 AES vacuum adapter

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4485678.

Customized version of https://www.thingiverse.com/thing:3385718

Created with Customizer! https://www.thingiverse.com/apps/customizer/run?thing_id=3385718



8 mm Trimmer comb for Phillips Multigroom 3000

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4382900.

Fits my Moto G3 just fine.


Customized version of https://www.thingiverse.com/thing:3727521

Created with Customizer! https://www.thingiverse.com/apps/customizer/run?thing_id=3727521



Phone stand Motorola Moto G3

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4365303.

Huge Funnel with vent.

Großer Trichter mit Druckausgleich.


Customized version of https://www.thingiverse.com/thing:1848038

Created with Customizer! https://www.thingiverse.com/apps/customizer/run?thing_id=1848038



Huge funnel with vent - Großer Trichter mit Druckausgleich 31mm

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4633530.

Do you also live in constant fear because your beloved sauces might fall out of the fridge door when you open it?
Fear no more, as this Sauce Retainer keeps your sauces from falling out and shattering on the floor like your dreams about chicken wings with hot sauce.

The rods in my fridge door have a diameter of 5 mm and are 13 mm apart.

I don't think anyone is ever going to print this, but if you do: Please let me know or post a make :)

Saucy!

Fridge door sauce retainer

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4467527.

Customized version of https://www.thingiverse.com/thing:4159541

Created with Customizer! https://www.thingiverse.com/apps/customizer/run?thing_id=4159541



5 mm Kabelklemme

Activity related to collaborating with others on models

Likes, comments, and activity from your community

A roundup of models that we think you'll like

For when we think someone might have posted your content as their own

New content from your premium memberships

Emails and messages from designers you follow

DrSchaumi