womp 3d model having fun with it remixable enjoy

low poly grandpa.stl

just a cute little thing i made in womp 3d

low poly dog.stl

made using womp-3d  thought it might be a fun easy way to try out get a quick project out.

low poly squidward

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:5674967.

dare your computer to slice this lmao,  itll take about 10 minutes minimum, 

  its a really small model tho so i scale mine up a bit

calibear v2 smoother HDer keychain bobble.

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:5648855.

justg a bottle cage thats designed around 0.4 nozzles and  being as retraction free as possible, given the weight

i have one of these on my bike just not mounted vertically as the last bottle on the printed verticle cage burst through the bottom.

enjoy!

bicycle bottle cage (good in pet G)

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:5648520.

designed this filament guide for the 20 20 rails on my ender 5   helps me after my direct drive conversion.

2020 rail clamp filament wire guide

kirby christmas ornament no hat

for your the last filament on the roll,  barely a couple grams it will probably print about 2 walls per and be around 30 minutes due to the fact its doing an inner wall as well and its hollow i was trying to print these clear but its still easily clouded send pics of your attempts

6mm potentiometer knobs 

6mmm knob designs v2_6mmm knob designs v2_Body2.stl

 meant to fit 6 games of your choice and expand the storage of your typical switch game case.
apply some tape to the inside and glue this print down to the tape layer  when the case is closed they may rattle some but will not fall out.

perfect for traveling

 nintendo switch game holder (holds 6)

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:5136146.

just a little pegboard tool holder design trying to help my shop dudes get cleaned up. good to know where each tool goes.  uses a little snowboard screw I found,  and a m5 nut i beveled the hole on it but typically, id be threading a screw into the back of it.

peg board tri tool holder- triple Allen key

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:5130414.

fits perfectly on the super b torque wrenches we have at work may work on others but have only tried the super b one recommend printing a little above 100% just because the bits were hard to get back out when they were put all the way in there but great replacement for the standard case that makes it easy to put away but hard to get back out. 



Torque wrench mount for pegboard 1" spaced

this is just a model  but i am personally going to try and use it more than once- you could also use this as a sand casting pattern

https://www.youtube.com/watch?v=gNQKYfBRPzM



 Print at your own risk - m5 31.8 stem no logo

body stem 31.8-1

face stem 31.8-1

id suggest printing on the largest flattest surfaces, you don't need supports for the overhangs but i did use some for certain things

this is designed for m5 bolts ranging from 20mm to 30mm long
except for the main bolt that tightens the sliding jaw onto your phone that is designed for quarter 20 lag bolts it will need to be atleast 3 inches for most cell phones but longer the better you can even add a spring to make it slide nicer,

total hardware

3 m5 bolts 3 m5 nuts
one 1/4 20 lag bolt one 1/4 20 nut

might be worth slimming down in the future so ill be uploading a v2 later

phone filmer handle - landscape

individual parts print from flattest surface

phone holder with handle.SLDPRT

use this model as u may i plan to gift this boy as a change jar or some sort of dish for the keys of my sweet wifey.
 I sink the model until the feet and hands give good flat spots to print from ideally you wont need supports the overhangs are not big

kirby a  toque.stl

skull embeded in his mouth is very  high detail (by accident) so the file itslef is big but i thought it was funny i lower it a bit into the bed so he sits absolutley flat

kirby with skull showing

kirby with skully2.stl

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:5029883.

personal blender model  funky lookin human skull i may play around with it make it look funkier!
getting better with blender but not much faster im having fun anyway

skull game anatomically inaccurate skull model

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4970244.

Hardcore solid works creativity here i tried my best without getting into blender try using the halves if its hard to print but I printed the whole thing from the bottom   it will turn out okay with a bit of supports 

I use a 65 degree overhang nothing to extreme but could use maybe a 55 degree
 
200 or 195 degree on my PLA OF CHOICE - polymaker polyterra


excuse the sound on the video playing with the shorts feaure lolling my ass off


halloween jackolantern

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4823122.

Start Organizing YOUR Tools this summer, its a long ish print depending on the infill 
This is a clamp on rack for an amazon allen key set my friend bought the clamp on the back is an inch wide and should also work on some thinner table tops or maybe a ridge on the wall.
check out my youtube link in my bio to see me make other stuff like this.

1 inch clamp allen key holder

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4967019.

thanks to James for the compliments that made me gush  glad to see the design tested unfortunately i use a laptop so im doomed to watch as others enjoy my creations 

so..........


PRINT THIS AND SEND ME PICTURESSSS 
that would get me excited i want to know how well it does or doesn't work

 there are however some extraneous fins that i dont think are necessary and i will be removing them from one version of the upload  happy printing fellows!

[https://www.youtube.com/watch?v=WGZQM5nu9QE](url)

 "OBB" by craftcentric Fan showdown entry major hardware

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4887527.

very simple design i made for my airbrush its got a 5mm spout and has no lid initially i was going to make one but the volume is so small. 

it holds a nice and small amount paint so when your doing detail works you can change colours quickly or mix them on the fly 

check out my youtube to see other printing projects i have in the future

airbrush cup 

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4918381.

my attempt at  a quick cable spooler device let me know how it turns out for you I've been printing mine with my 1mm nozzle so I accidentally skipped some steps in he x and y maybe your slicer settings may turn out better than mine, 

feel free to remix but my version I'm sure isn't the best but its the my own design and for me that has value :) .


enjoy a little video of me printing and using the two versions I designed so far and let me know what you think in the comments I have a few more projects to finish uploading (so subscribe), writing it out is the hardest part.

cable spooler small/medium

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4870392.

check out the time-lapse video of it being printed below its just  to show how it goes without brim or supports.


just a tiny piece i gave myself to encourage me to use my whiteboard by making the markers more accessible, on my whiteboard it has a nice rubber edge on the bottom and top so i tucked the hook into the frame and it has never moved elsewhere.

https://www.tiktok.com/@craftcentric/video/6960407746462158086?is_copy_url=0&is_from_webapp=v1&sender_device=pc&sender_web_id=6914486740436043270

marker tray- hooks into  my whiteboard

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4892461.

my little, attempt at a print in place feature, modeled a floating collar into the screwdriver to give the user something to grab while turning if working on small items. 

it is also just a cool feature to test your printer tolerances this one has a 0.4mm gap when printing, and worked well with like 5% support density.
 after its printed you'll have to cut the supports out of the bottom of the collar but its not especially difficult however this was usually when I'd accidentally break off the tip.

the bit opening also has a little hole you can drop a magnet into to make it even more convenient.


 screwdriver - stubby print in place, spinning collar 

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4851029.

this was a custom piece for my friend he very nicely paid me for its the outside corner for an led wall mount usually the kits only come with inside corners, so this is a really helpful item for people in condos or places with irregular ceilings, the bracket itself is used for v shape aluminum channel, the 45 degree style



 led brands:	
GUSODOR , Vasmok , lustreon, yi-lighting

led string light outside corner

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4893581.

are you stuck with muddy colours on your paintings, maybe the issue is not having a proper palette to mix with.

even better you get a little water reservoir to clean the palette , and brush with keeping your main water supply cleaner for longer.

https://youtu.be/DxY5bnpu0Q0


water color painting tray, quick design with some medium draft i may end up doing some casts of this so i can make it in a clear material if you have a resin printer this is a good model but on an fdm printer the layer lines are very noticeable however I printed this on its end  so the layer lines all go along the length of it



paint tray water color

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4981664.

a bit of a proof of concept you can print everything but you SHOULDNT  print everything

this takes m5 bolts but is not a model with threads you will be threading it yourself when you start the bolts in i used it on a bike but only as a joke or a gimmick if you try it send me pictures its funny

35mm bike stem test your metal!?

https://www.youtube.com/channel/UCLM1DMDIGg7Ntp4ZwWyIPbA

Activity related to collaborating with others on models

Likes, comments, and activity from your community

A roundup of models that we think you'll like

Craftcentric