Cover_278001993.stl

I accidently broke the cover for the speed sensor so I made a new one for replacement as there is no original spare for the cover only.

Fits sensor with P/N: 278001993

If you like what I'm doing, please consider supporting me
https://www.buymeacoffee.com/taguvove

Snoopy wind vane

Sea-Doo waterpump impeller tool

Jeep Grand Cherokee ZJ PowerAntenna gears

Trench club

Corner Bumper 291001505

Drawer key

Ryze Tello Battery adapter

Dart Fastex 293730024

Paint booth "Bender"

4pin socket tool

Sea-Doo front arm

QUERCETTI rail pillar

Sword-Ninja

Pelican case wheels

Drive Shaft Plug

Child lock / Barnlås Elfa Classic slide door

Front axle Bruder Tractor

Breather connector

Seadoo Compressor support plate 529035947

adapter for biltema  86-051

Sealing Ring

Child lock / Barnlås Vedum XP-lådan

Moustrape game Cheeze plate

Oral-B Batman costume

Bosch flange bearing

Bruder excavator bucket

Fiskars scissors protection

Gear switch arm

Garden outside tap key

Flanged Bushing 293900042.stl

My spacer for the off power steering had broken so I needed to make a new one.
Use together with a suitable stainless steel washer on the outside.



If you like what I'm doing, please consider supporting me
https://www.buymeacoffee.com/taguvove

Bumper_V2_291001505.stl

Corner Bumper 291001505 For Sea-Doo
The original ones where so damages and scratched so I decided to make my own ones.

I also made them hollow with ventilation to get a more bumpy function on it compared to the original, see station view to get an understanding.

If you like what I'm doing, please consider supporting me
https://www.buymeacoffee.com/taguvove

Neoprene Seal 293200087

Simple seal ring for jetpump on a seadoo


Seadoo equivalent P/N: 293200087
Original made in neoprene, should be ok to print in TPU as well

If you like what I'm doing, please consider supporting me
https://www.buymeacoffee.com/taguvove

Impeller-Cover_267000262.stl

My impeller cover was broken and I had to make a new one.

If you like what I'm doing, please consider supporting me
https://www.buymeacoffee.com/taguvove

Timing-chain_tensioner_420236540.stl

Timing chain tensioner for seadoo engine, 4-teh engine

If you like what I'm doing, please consider supporting me
https://www.buymeacoffee.com/taguvove

Camshaft-Cover_420660100.stl

Camshaft cover for seadoo engine 4-tech
If you like what I'm doing, please consider supporting me
https://www.buymeacoffee.com/taguvove

Fuel-Tank-Cap_275500430.stl

My fuel tank cap was cracked and needed a replacement. I decided to do my own.
This replaces only the top cap and not the threaded part.

The original had styrofoam inside, (I guess is to make it buoyant in case of loss). I made mine hollow in the slicing software (3mm) and after printing I sealed the venting holes with resin to make is water tight and buoyant.

Finally some pain to make it look better.

If you like what I'm doing, please consider supporting me
https://www.buymeacoffee.com/taguvove

Nyckel.3mf

Needed a key for an old drawer. Inspired by the original key

Supercharger_Clutch_Gear_Tool-LONG.stl

Tool to hold the supercharger gear for measuring slip
This is instead of using the original hook spanner.

For use on seadoo Supercharger.

I made two versions one 100mm long
and one 150mm long.

If you like what I'm doing, please consider supporting me
https://www.buymeacoffee.com/taguvove

Supercharger_Clutch_Gear_Tool

Tool to hold the supercharger gear for measuring slip.
This is instead of using the original hook spanner.

For idé sök seadoo Supercharger

I made two versions one 100mm long
and one 150mm long.

If you like what I'm doing, please consider supporting me
https://www.buymeacoffee.com/taguvove

Lever_271000986.stl

The reverse lever on my Jetski was broken and I couldn't source one locally so I made my own.

If you like what I'm doing, please consider supporting me
https://www.buymeacoffee.com/taguvove

Retainer-Latch_269500820.stl

The latches for my ""glove department" where broken and I couldn't source them locally so I decided to make my own.

This replaces the original P/N: 269 500 820

If you like what I'm doing, please consider supporting me
https://www.buymeacoffee.com/taguvove

piston_ring-tool.stl

This is a piston rings tool for pistons with a diameter of 100mm
I made this during engine renovation of my Sea-Doo RXP.

Use a M6x35mm if you wish to press and hold the rings in place while mounting.
I just clamped mine by hand and it works as well.

Recommended after printing is to grind the inside smooth so the piston rings doesn't stuck to the layer lines.

If you like what I'm doing, please consider supporting me
https://www.buymeacoffee.com/taguvove

Sea-Doo_Waterpump_impeller_420922801.stl

This is a tool for removing Sea-Doo waterpump impeller.
It fits over the impeller blades.
There are two versions, one with a handle and one with 1/2 inch square socket.

If you like what I'm doing, please consider supporting me
https://www.buymeacoffee.com/taguvove

Sea-Doo_420922801.stl

Sea-Doo_Water-pump_Impeller_Tool_half-inch.stl

Sea-Doo_Wear-ring_267000105.stl

Waterpump impelelr for seadoo 4-tec enginges.
This model have implemented M8 lefthand threaded hole to fit directly on the shaft.

If you like what I'm doing, please consider supporting me
https://www.buymeacoffee.com/taguvove

Sea-Doo_267000105.stl

Grommet 293_720_042.stl

Grommet.
Fits Sea-Doo rxp and others.
original P/N: 293 720 042

293_720_042.stl

Front cover hinge 269_500_704.stl

Sea-Doo front cover hinge.
Custom made replacement for Sea-Doo original hinge with P/N: 269 500 704


found on Sea-Doo RXP and others

269_500_704.stl

Activity related to collaborating with others on models

Likes, comments, and activity from your community

New content from your premium memberships

Emails and messages from designers you follow

Get notified when someone purchases your models or memberships

Chipen83

Achievements

Sequoia

Up and Coming

Explorer