**Print-In-Place, No Supports, Articulating Fidget Toy**

**Subscribe To the [Mimetics 3D Commercial Tier on Thangs.](https://than.gs/u/934587?plans=true) for rights to sell prints of your cool new friend.**

**[Have you noticed that Bony Basilisk has a NEW FRIEND?](https://than.gs/m/964165)**

Emerging from the crypts and cursed castles, the Bony Basilisk is here to bewitch and bedazzle just in time for the spooky season! With its detailed skeletal structure, this bony behemoth is prepared to perch on your shelf as the haunting highlight of your Halloween assembly or stand sentinel, casting a bone-chilling shadow for your guests.  This ancient creature refuses to let the ghosts, ghouls, and dragons have all the fall-time fun on their own.

This Bony Basilisk is the third creation in a series of Snap-Flex models by Mimetics 3D, and it's available for free for a limited time.

**Snap-Flex Collection:**
This articulated fidget toy integrates the Mimetics 3D "Snap-Flex" joint. This allows it to both move smoothly, mimicking the fluid motion of living creatures, AND stabilize in a firm pose, providing a premium fidgeting experience. 

Each **SNAP** will resonate as a symphony of satisfaction to your ears, confirming your masterful manipulations.

**Snap-Flex Instructions:**
To Lock: Push Body Segments together
To Unlock: Pull Body Segments Apart


**Tolerance:**
To accommodate different printer settings and filaments, I’m uploading 3 different tolerance levels for the Bone Snake to ensure that you get the best fitting, most satisfying “SNAP” with each of your prints.

This is the **Tight** tolerance model.  For the other tolerances, please check out the other versions of the model below:

**Medium Tolerance Extra Long Bony Basilisk:**
https://than.gs/m/942873
**Loose Tolerance Extra Long Bony Basilisk:**
https://than.gs/m/942878

Please try out each to see what works best for you, and let me know which version you prefer!

**Other Models:**

If you like this Bony Basilisk, be sure to check out the latest articulated model here:

**Tight Tolerance Frostbite:**
https://than.gs/m/964164
**Medium Tolerance Frostbite:**
https://than.gs/m/964165
**Loose Tolerance Frostbite:**
https://than.gs/m/964166


Make sure to revisit us frequently for more thrilling Snap-Flex models to come. We're eager to hear your feedback and collaborate on refining this model going forward.

This model is for personal use only. If you're interested in selling physical prints of this model, please subscribe to the [Mimetics 3D Commercial Tier on Thangs.](https://than.gs/u/934587?plans=true)

**Print Settings:**
0.2mm Layer Height
3 Wall Loops
3 Top Shell Layers
Brim Suggested

**Suggested Material: PLA or PLA+**
**Note:** Silk PLA is too weak to hold up to repeated use of the Snap-Flex joint.  Use silks at your own risk


**No Supports, Print-In-Place at 100% scale** 
Printing any smaller may disable the Snap-Flex joint.

Printing larger than 100% will make the snap louder AND **harder to pop**, so be sure to do a shorter test print to make sure it's not **TOO hard to snap into place.**

These tolerances are TIGHT and you'll likely have to snap each segment a few times before it's loose enough to snap/unsnap easily. I recommend you use regular PLA or PLA+. ABS might be even better, but I haven't tried it yet.

If you print this in resin, please let me know how it turns out. I imagine you would need a more flexible/less stiff resin for it to work appropriately.

Extra Long Bony Basilisk - Articulated Snap-Flex Fidget (Tight Joints)

Print-In-Place, No Supports, Articulating Fidget Toy

Emerging from the crypts and cursed castles, the Bony Basilisk is here to bewitch and bedazzle just in time for the spooky season! With its detailed skeletal structure, this bony behemoth is prepared to perch on your shelf as the haunting highlight of your Halloween assembly or stand sentinel, casting a bone-chilling shadow for your guests.  This ancient creature refuses to let the ghosts, ghouls, and dragons have all the fall-time fun on their own.

This articulated fidget toy integrates the Mimetics 3D "Snap-Flex" joint. This allows the Bony Basilisk to both move smoothly, mimicking the fluid motion of living creatures, AND stabilize in a firm pose, providing a premium fidgeting experience. Each SNAP will resonate as a symphony of satisfaction to your ears, confirming your masterful manipulations.

This Bony Basilisk is the third creation in a series of Snap-Flex models by Mimetics 3D, and it's available for free for a limited time.

Tolerance:
To accommodate different printer settings and filaments, I’m uploading 3 different tolerance levels for the Bone Snake to ensure that you get the best fitting, most satisfying “SNAP” with each of your prints.

This is the Tight tolerance model.  For the other tolerances, please check out the other versions of the model below:

Tight Tolerance Extra Long Bony Basilisk:
Coming Soon
Loose Tolerance Long Bony Basilisk:
Coming Soon

Please try out each to see what works best for you, and let me know which version you prefer!


Make sure to revisit us frequently for more thrilling Snap-Flex models to come. We're eager to hear your feedback and collaborate on refining this model going forward.

This model is for personal use only. If you're interested in selling physical prints of this model, please subscribe to the Mimetics 3D Commercial Tier on Thangs.

Print Settings:
0.2mm Layer Height
3 Wall Loops
3 Top Shell Layers
No Supports, Print-In-Place at 100% scale.  Going any smaller may disable the Snap-Flex joint.

These tolerances are TIGHT and you'll likely have to snap each segment a few times before it's loose enough to snap/unsnap easily. I recommend you use regular PLA or PLA+. ABS might be even better, but I haven't tried it yet.

Silk PLA is a bit softer and may not click as nicely. I'd also be more concerned about silk PLA holding up to the wear and tear.
If you print this in resin, please let me know how it turns out. I imagine you would need a more flexible/less stiff resin for it to work appropriately.

License: Attribution-NonCommercial-NoDerivs
CC BY-NC-ND
***
***Sculpt by @ChelsC423***
***
***If you would like to sell physical objects, please see the Chaos Core Partner tier on our Patreon***
***
If you would like to support us and receive exclusive to Patron models every month check us out here:
https://www.patreon.com/chaoscoretech

Ornate Charizard Skull (Pokémon)

OrnateCharizardSkull.stl

Hollow Skull - Pencil Holder - Decor
If you like my work find more here - https://www.myminifactory.com/users/printedobsession
if you want to support my work consider joining patreon - https://www.patreon.com/printedobsession
want to know more about my process? i have tutorials on youtube - https://www.youtube.com/c/PrintedObsession

CC BY-NC-ND
This license allows users to copy and distribute the material in any medium or format in unadapted form only, for noncommercial purposes only, and only so long as attribution is given to the creator.

Hollow Skull - Pencil Holder - Decor

Ornate Cubone Skull (Pokemon)

Cubone.stl

**Print-In-Place, No Supports, Articulating Fidget Toy**

**Subscribe To the [Mimetics 3D Commercial Tier on Thangs.](https://than.gs/u/934587?plans=true) for rights to sell prints of your cool new friend.**

Emerging from the crypts and cursed castles, the Bony Basilisk is here to bewitch and bedazzle just in time for the spooky season! With its detailed skeletal structure, this bony behemoth is prepared to perch on your shelf as the haunting highlight of your Halloween assembly or stand sentinel, casting a bone-chilling shadow for your guests.  This ancient creature refuses to let the ghosts, ghouls, and dragons have all the fall-time fun on their own.

This Bony Basilisk is the third creation in a series of Snap-Flex models by Mimetics 3D, and it's available for free for a limited time.

**Snap-Flex Collection:**
This articulated fidget toy integrates the Mimetics 3D "Snap-Flex" joint. This allows it to both move smoothly, mimicking the fluid motion of living creatures, AND stabilize in a firm pose, providing a premium fidgeting experience. 

Each **SNAP** will resonate as a symphony of satisfaction to your ears, confirming your masterful manipulations.

**Snap-Flex Instructions:**
To Lock: Push Body Segments together
To Unlock: Pull Body Segments Apart


**Tolerance:**
To accommodate different printer settings and filaments, I’m uploading 3 different tolerance levels for the Bone Snake to ensure that you get the best fitting, most satisfying “SNAP” with each of your prints.

This is the **Medium** tolerance model.  For the other tolerances, please check out the other versions of the model below:

**Tight Tolerance Extra Long Bony Basilisk:**
https://than.gs/m/942802
**Loose Tolerance Extra Long Bony Basilisk:**
https://than.gs/m/942878

Please try out each to see what works best for you, and let me know which version you prefer!


**Other Models:**

If you like this Bony Basilisk, be sure to check out the latest articulated model here:
**Tight Tolerance Cold Snap:**
https://than.gs/m/960229
**Medium Tolerance Cold Snap:**
https://than.gs/m/960234
**Loose Tolerance Cold Snap:**
https://than.gs/m/960235


Make sure to revisit us frequently for more thrilling Snap-Flex models to come. We're eager to hear your feedback and collaborate on refining this model going forward.

This model is for personal use only. If you're interested in selling physical prints of this model, please subscribe to the [Mimetics 3D Commercial Tier on Thangs.](https://than.gs/u/934587?plans=true)

**Print Settings:**
0.2mm Layer Height
3 Wall Loops
3 Top Shell Layers
Brim Suggested

**Suggested Material: PLA or PLA+**
**Note:** Silk PLA is too weak to hold up to repeated use of the Snap-Flex joint.  Use silks at your own risk


**No Supports, Print-In-Place at 100% scale** 
Printing any smaller may disable the Snap-Flex joint.

Printing larger than 100% will make the snap louder AND **harder to pop**, so be sure to do a shorter test print to make sure it's not **TOO hard to snap into place.**

These tolerances are TIGHT and you'll likely have to snap each segment a few times before it's loose enough to snap/unsnap easily. I recommend you use regular PLA or PLA+. ABS might be even better, but I haven't tried it yet.

If you print this in resin, please let me know how it turns out. I imagine you would need a more flexible/less stiff resin for it to work appropriately.

Extra Long Bony Basilisk - Articulated Snap-Flex Fidget (Medium Tightness Joints)

**Print-In-Place, No Supports, Articulating Fidget Toy**

Emerging from the crypts and cursed castles, the Bony Basilisk is here to bewitch and bedazzle just in time for the spooky season! With its detailed skeletal structure, this bony behemoth is prepared to perch on your shelf as the haunting highlight of your Halloween assembly or stand sentinel, casting a bone-chilling shadow for your guests.  This ancient creature refuses to let the ghosts, ghouls, and dragons have all the fall-time fun on their own.

This articulated fidget toy integrates the Mimetics 3D "Snap-Flex" joint. This allows the Bony Basilisk to both move smoothly, mimicking the fluid motion of living creatures, AND stabilize in a firm pose, providing a premium fidgeting experience. Each **SNAP** will resonate as a symphony of satisfaction to your ears, confirming your masterful manipulations.

This Bony Basilisk is the third creation in a series of Snap-Flex models by Mimetics 3D, and it's available for free for a limited time.

**Tolerance:**
To accommodate different printer settings and filaments, I’m uploading 3 different tolerance levels for the Bone Snake to ensure that you get the best fitting, most satisfying “SNAP” with each of your prints.

This is the **Medium** tolerance model.  For the other tolerances, please check out the other versions of the model below:

**Tight Tolerance Extra Long Bony Basilisk:**
https://than.gs/m/942802
**Loose Tolerance Extra Long Bony Basilisk:**
Coming Soon

Please try out each to see what works best for you, and let me know which version you prefer!


Make sure to revisit us frequently for more thrilling Snap-Flex models to come. We're eager to hear your feedback and collaborate on refining this model going forward.

This model is for personal use only. If you're interested in selling physical prints of this model, please subscribe to the Mimetics 3D Commercial Tier on Thangs.

**Print Settings:**
0.2mm Layer Height
3 Wall Loops
3 Top Shell Layers
No Supports, Print-In-Place at 100% scale.  Going any smaller may disable the Snap-Flex joint.

These tolerances are TIGHT and you'll likely have to snap each segment a few times before it's loose enough to snap/unsnap easily. I recommend you use regular PLA or PLA+. ABS might be even better, but I haven't tried it yet.

Silk PLA is a bit softer and may not click as nicely. I'd also be more concerned about silk PLA holding up to the wear and tear.
If you print this in resin, please let me know how it turns out. I imagine you would need a more flexible/less stiff resin for it to work appropriately.

**Print-In-Place, No Supports, Articulating Fidget Toy**

**Subscribe To the [Mimetics 3D Commercial Tier on Thangs.](https://than.gs/u/934587?plans=true) for rights to sell prints of your cool new friend.**

**Find the Bony Basilisk's magical little feline friend over here:** https://than.gs/m/940296

Emerging from the crypts and cursed castles, the Bony Basilisk is here to bewitch and bedazzle just in time for the spooky season! With its detailed skeletal structure, this bony behemoth is prepared to perch on your shelf as the haunting highlight of your Halloween assembly or stand sentinel, casting a bone-chilling shadow for your guests.  This ancient creature refuses to let the ghosts, ghouls, and dragons have all the fall-time fun on their own.

This Bony Basilisk is the third creation in a series of Snap-Flex models by Mimetics 3D, and it's available for free for a limited time.


**Snap-Flex Collection:**
This articulated fidget toy integrates the Mimetics 3D "Snap-Flex" joint. This allows it to both move smoothly, mimicking the fluid motion of living creatures, AND stabilize in a firm pose, providing a premium fidgeting experience. 

Each **SNAP** will resonate as a symphony of satisfaction to your ears, confirming your masterful manipulations.

**Snap-Flex Instructions:**
To Lock: Push Body Segments together
To Unlock: Pull Body Segments Apart


**Tolerance:**
To accommodate different printer settings and filaments, I’m uploading 3 different tolerance levels for the Bone Snake to ensure that you get the best fitting, most satisfying “SNAP” with each of your prints.

This is the **Medium** tolerance model.  For the other tolerances, please check out the other versions of the model below:

**Tight Tolerance Long Bony Basilisk:**
https://than.gs/m/936921
**Loose Tolerance Long Bony Basilisk:**
https://than.gs/m/937052

Please try out each to see what works best for you, and let me know which version you prefer!


**Other Models:**

If you like this Bony Basilisk, be sure to check out the latest articulated model here:
**Tight Tolerance Cold Snap:**
https://than.gs/m/960229
**Medium Tolerance Cold Snap:**
https://than.gs/m/960234
**Loose Tolerance Cold Snap:**
https://than.gs/m/960235


Make sure to revisit us frequently for more thrilling Snap-Flex models to come. We're eager to hear your feedback and collaborate on refining this model going forward.

This model is for personal use only. If you're interested in selling physical prints of this model, please subscribe to the [Mimetics 3D Commercial Tier on Thangs.](https://than.gs/u/934587?plans=true)

**Print Settings:**
0.2mm Layer Height
3 Wall Loops
3 Top Shell Layers
Brim Suggested

**Suggested Material: PLA or PLA+**
**Note:** Silk PLA is too weak to hold up to repeated use of the Snap-Flex joint.  Use silks at your own risk


**No Supports, Print-In-Place at 100% scale** 
Printing any smaller may disable the Snap-Flex joint.

Printing larger than 100% will make the snap louder AND **harder to pop**, so be sure to do a shorter test print to make sure it's not **TOO hard to snap into place.**

These tolerances are TIGHT and you'll likely have to snap each segment a few times before it's loose enough to snap/unsnap easily. I recommend you use regular PLA or PLA+. ABS might be even better, but I haven't tried it yet.

If you print this in resin, please let me know how it turns out. I imagine you would need a more flexible/less stiff resin for it to work appropriately.

Long Bony Basilisk - Articulated Snap-Flex Fidget (Medium Joints)

**Print-In-Place, No Supports, Articulating Fidget Toy**

Emerging from the crypts and cursed castles, the Bony Basilisk is here to bewitch and bedazzle just in time for the spooky season! With its detailed skeletal structure, this bony behemoth is prepared to perch on your shelf as the haunting highlight of your Halloween assembly or stand sentinel, casting a bone-chilling shadow for your guests.  This ancient creature refuses to let the ghosts, ghouls, and dragons have all the fall-time fun on their own.

This articulated fidget toy integrates the Mimetics 3D "Snap-Flex" joint. This allows the Bony Basilisk to both move smoothly, mimicking the fluid motion of living creatures, AND stabilize in a firm pose, providing a premium fidgeting experience. Each **SNAP** will resonate as a symphony of satisfaction to your ears, confirming your masterful manipulations.

This Bony Basilisk is the third creation in a series of Snap-Flex models by Mimetics 3D, and it's available for free for a limited time.


**Tolerance:**
To accommodate different printer settings and filaments, I’m uploading 3 different tolerance levels for the Bone Snake to ensure that you get the best fitting, most satisfying “SNAP” with each of your prints.

This is the **Medium** tolerance model.  For the other tolerances, please check out the other versions of the model below:

**Tight Tolerance Long Bony Basilisk:**
https://than.gs/m/936921
**Loose Tolerance Long Bony Basilisk:**
Coming Soon

Please try out each to see what works best for you, and let me know which version you prefer!

**Other Models:**
If you like the Long Bony Basilisk, be sure to check out it’s cute younger sibling, the Short Bony Basilisk:

**Tight Tolerance Short Bony Basilisk:**
https://than.gs/m/936954
**Medium Tolerance Short Bony Basilisk:**
https://than.gs/m/937047
**Loose Tolerance Short Bony Basilisk:**
https://than.gs/m/937048

Make sure to revisit us frequently for more thrilling Snap-Flex models to come. We're eager to hear your feedback and collaborate on refining this model going forward.

This model is for personal use only. If you're interested in selling physical prints of this model, please subscribe to the Mimetics 3D Commercial Tier on Thangs.

**Print Settings:**
0.2mm Layer Height
3 Wall Loops
3 Top Shell Layers
No Supports, Print-In-Place at 100% scale.  Going any smaller may disable the Snap-Flex joint.

These tolerances are TIGHT and you'll likely have to snap each segment a few times before it's loose enough to snap/unsnap easily. I recommend you use regular PLA or PLA+. ABS might be even better, but I haven't tried it yet.

Silk PLA is a bit softer and may not click as nicely. I'd also be more concerned about silk PLA holding up to the wear and tear.
If you print this in resin, please let me know how it turns out. I imagine you would need a more flexible/less stiff resin for it to work appropriately.

Demon Skull - Decoration
If you like my work find more here - https://www.myminifactory.com/users/printedobsession
if you want to support my work consider joining patreon - https://www.patreon.com/printedobsession
want to know more about my process? i have tutorials on youtube - https://www.youtube.com/c/PrintedObsession

CC BY-NC-ND
This license allows users to copy and distribute the material in any medium or format in unadapted form only, for noncommercial purposes only, and only so long as attribution is given to the creator.


Demon Skull - Decoration

This human skull model can be used for learning anatomy or just freaking out your friends. See here for assembly video: https://youtu.be/dm0RT-1eFFc
To assemble with magnets, you will need:
•	66 of 1/8” x 1/16” cylindrical
•	36 of 1/4” x 1/8” cylindrical
www.kjmagnetics.com is a good source of magnets.
Files are provided in anatomical orientation. You will need to reorient and prepare them according to your preferences, equipment, and skill level. Here are some considerations:
•	Orient outer surfaces upwards so that the surfaces in contact with support structures are less visible in the final model.
•	As much as possible, avoid orienting the magnetic anchors downwards. There are some situations in which this is unavoidable. These can be cleaned up post-print.
Here are considerations for assembly:
•	Before inserting magnets, clean out the magnet anchors with a 1/8” or 1/4” drill bit to remove any imperfections, allowing the magnets to sit properly.
•	Ensure that you insert magnets with polarity oriented to allow proper connection of bones.
•	You may need to use glue to secure some of the magnets in place. CA glue works well.
Every attempt has been made to maintain anatomical correctness; however, the following small modifications were necessary to optimize the files for 3D printing:
•	The nasal bones, lacrimal bones and upper teeth are fused to ipsilateral maxilla. Lower teeth are fused to the mandible. They are too small and thin to print and assemble on their own.
•	Some areas of bone have been thickened to support the magnet anchors.
•	Gaps have been created or expended between fused joints to allow these bones to be separated.
•	The perpendicular plate of the ethmoid bone has been removed. It is too thin and there is limited space for it to fit properly.
•	Bones of the inner ear are not included.
•	This model includes only bony structures.
"BodyParts3D, © The Database Center for Life Science licensed under CC Attribution-Share Alike 2.1 Japan".


Full Size Anatomically-Correct 18-Piece Magnetic Human Skull Model

Full Skull Display model.stl

Elevate your home decor with a fusion of style and functionality with our Skull Phone Holder 3D model at Thangs.com. The creativity imbibed in this unique design makes it a great accessory and an absolute stand-out in our "Home & Garden" category. Intricately designed by printedobsession, this striking skull-shaped phone holder is not just visually engaging, but it also promises utility and convenience. With this innovative design, you'll never have to worry about misplacing your phone ever again. The detailed images from various angles allow you to visualize how the model would add an edge to your living space, making it an instant conversation starter. The skull phone holder is not just appealing but also a testament to striking details crafted to perfection. For more insights into this 3D model, you can visit our website. Remember, your space speaks about you. Make it loud

Skull Phone Holder - Home Decoration

Cubone - Pokemon - Fan Art
If you like my work find more here - https://www.myminifactory.com/users/printedobsession
if you want to support my work consider joining patreon - https://www.patreon.com/printedobsession
want to know more about my process? i have tutorials on youtube - https://www.youtube.com/c/PrintedObsession

CC BY-NC-ND
This license allows users to copy and distribute the material in any medium or format in unadapted form only, for noncommercial purposes only, and only so long as attribution is given to the creator.

Cubone - Pokemon - Fan Art

License: Attribution-NonCommercial-NoDerivs
CC BY-NC-ND
***
***Sculpt by @ChelsC423***

***
***If you would like to sell physical objects, please see the CCT Partner tier on our Patreon***
***
If you would like to support me AND receive exclusive to Patron models every month check me out here:
https://www.patreon.com/chelscct


Ornate Mewtwo Skull (Pokémon)

Ornate Mew Skull (Pokémon)

Vampire Skull - Decoration
If you like my work find more here - https://www.myminifactory.com/users/printedobsession
if you want to support my work consider joining patreon - https://www.patreon.com/printedobsession
want to know more about my process? i have tutorials on youtube - https://www.youtube.com/c/PrintedObsession

CC BY-NC-ND
This license allows users to copy and distribute the material in any medium or format in unadapted form only, for noncommercial purposes only, and only so long as attribution is given to the creator.

Vampire Skull - Decoration

Masked Skull - Decoration
If you like my work find more here - https://www.myminifactory.com/users/printedobsession
if you want to support my work consider joining patreon - https://www.patreon.com/printedobsession
want to know more about my process? i have tutorials on youtube - https://www.youtube.com/c/PrintedObsession

CC BY-NC-ND
This license allows users to copy and distribute the material in any medium or format in unadapted form only, for noncommercial purposes only, and only so long as attribution is given to the creator.


Masked Skull - Decoration

Mech Skull - cyberpunk - Decoration 
If you like my work find more here - https://www.myminifactory.com/users/printedobsession
if you want to support my work consider joining patreon - https://www.patreon.com/printedobsession
want to know more about my process? i have tutorials on youtube - https://www.youtube.com/c/PrintedObsession

CC BY-NC-ND
This license allows users to copy and distribute the material in any medium or format in unadapted form only, for noncommercial purposes only, and only so long as attribution is given to the creator.

Mech Skull - cyberpunk - Decoration 

Discover a unique 3D printed Skull Bowl, one of the standout pieces in the Arts & Entertainment category on thangs.com. This spooky yet fascinating Halloween decoration is the perfect addition to any haunting collection. Designed by Printed Obsession, the Skull Bowl brings a blend of artistic creativity and utility, offering an eerie bowl disguised as a realistic human skull. Ideal as a Halloween decoration, it takes Halloween-themed party essentials to a new level, providing an excellent talking point for your guests while doubling as serving bowls for sweet treats or fruits. Dip into the detailed images provided to get an up-close glimpse into the fantastic details of this 3D model before you bring it to life. With all aspects, from the hollowed-out cranium to the detailed facial features, it's clear this model was meticulously crafted by experts. Dive into our expanding library for more amazing Halloween models!

Skull Bowl - Halloween Decoration

Hey, if you’re in the neighbourhood drop by for a… CUP OF TEETH!!!! WHOA HA HA HA!

See here for video: https://youtu.be/UJhcGGX8jhM 

Teeth Cup: https://social.thangs.com/m/377780 
Teeth Saucer: https://social.thangs.com/m/377781 


BONUS: Comes with a full set of adult teeth!

The model pictured is printed with Eryone Matte Dew White PLA filament.

Teeth Cup

Hey, if you’re in the neighbourhood drop by for a… CUP OF TEETH!!!! WHOA HA HA HA!

See here for video: https://youtu.be/UJhcGGX8jhM 

Teeth Cup:
Teeth Saucer:

BONUS: Comes with a full set of adult teeth!


Full Set of Adult Teeth.stl

Teeth Cup (no handle).stl

Satur Skull - Decoration
If you like my work find more here - https://www.myminifactory.com/users/printedobsession
if you want to support my work consider joining patreon - https://www.patreon.com/printedobsession
want to know more about my process? i have tutorials on youtube - https://www.youtube.com/c/PrintedObsession

CC BY-NC-ND
This license allows users to copy and distribute the material in any medium or format in unadapted form only, for noncommercial purposes only, and only so long as attribution is given to the creator. 

Satur Skull - Decoration 

**Print-In-Place, No Supports, Articulating Fidget Toy**

**Subscribe To the [Mimetics 3D Commercial Tier on Thangs.](https://than.gs/u/934587?plans=true) for rights to sell prints of your cool new friend.**

Emerging from the crypts and cursed castles, the Bony Basilisk is here to bewitch and bedazzle just in time for the spooky season! With its detailed skeletal structure, this bony behemoth is prepared to perch on your shelf as the haunting highlight of your Halloween assembly or stand sentinel, casting a bone-chilling shadow for your guests.  This ancient creature refuses to let the ghosts, ghouls, and dragons have all the fall-time fun on their own.

This Bony Basilisk is the third creation in a series of Snap-Flex models by Mimetics 3D, and it's available for free for a limited time.

**Snap-Flex Collection:**
This articulated fidget toy integrates the Mimetics 3D "Snap-Flex" joint. This allows it to both move smoothly, mimicking the fluid motion of living creatures, AND stabilize in a firm pose, providing a premium fidgeting experience. 

Each **SNAP** will resonate as a symphony of satisfaction to your ears, confirming your masterful manipulations.

**Snap-Flex Instructions:**
To Lock: Push Body Segments together
To Unlock: Pull Body Segments Apart



**Tolerance:**
To accommodate different printer settings and filaments, I’m uploading 3 different tolerance levels for the Bone Snake to ensure that you get the best fitting, most satisfying “SNAP” with each of your prints.

This is the **Loose** tolerance model.  For the other tolerances, please check out the other versions of the model below:

**Tight Tolerance Extra Long Bony Basilisk:**
https://than.gs/m/942802
**Medium Tolerance Extra Long Bony Basilisk:**
https://than.gs/m/942873

Please try out each to see what works best for you, and let me know which version you prefer!

**Other Models:**

If you like this Bony Basilisk, be sure to check out the latest articulated model here:
**Tight Tolerance Cold Snap:**
https://than.gs/m/960229
**Medium Tolerance Cold Snap:**
https://than.gs/m/960234
**Loose Tolerance Cold Snap:**
https://than.gs/m/960235


Make sure to revisit us frequently for more thrilling Snap-Flex models to come. We're eager to hear your feedback and collaborate on refining this model going forward.

This model is for personal use only. If you're interested in selling physical prints of this model, please subscribe to the [Mimetics 3D Commercial Tier on Thangs.](https://than.gs/u/934587?plans=true)

**Print Settings:**
0.2mm Layer Height
3 Wall Loops
3 Top Shell Layers
Brim Suggested

**Suggested Material: PLA or PLA+**
**Note:** Silk PLA is too weak to hold up to repeated use of the Snap-Flex joint.  Use silks at your own risk


**No Supports, Print-In-Place at 100% scale** 
Printing any smaller may disable the Snap-Flex joint.

Printing larger than 100% will make the snap louder AND **harder to pop**, so be sure to do a shorter test print to make sure it's not **TOO hard to snap into place.**

These tolerances are TIGHT and you'll likely have to snap each segment a few times before it's loose enough to snap/unsnap easily. I recommend you use regular PLA or PLA+. ABS might be even better, but I haven't tried it yet.

If you print this in resin, please let me know how it turns out. I imagine you would need a more flexible/less stiff resin for it to work appropriately.

Extra Long Bony Basilisk - Articulated Snap-Flex Fidget (Loose Joints)

**Print-In-Place, No Supports, Articulating Fidget Toy**

Emerging from the crypts and cursed castles, the Bony Basilisk is here to bewitch and bedazzle just in time for the spooky season! With its detailed skeletal structure, this bony behemoth is prepared to perch on your shelf as the haunting highlight of your Halloween assembly or stand sentinel, casting a bone-chilling shadow for your guests.  This ancient creature refuses to let the ghosts, ghouls, and dragons have all the fall-time fun on their own.

This articulated fidget toy integrates the Mimetics 3D "Snap-Flex" joint. This allows the Bony Basilisk to both move smoothly, mimicking the fluid motion of living creatures, AND stabilize in a firm pose, providing a premium fidgeting experience. Each **SNAP** will resonate as a symphony of satisfaction to your ears, confirming your masterful manipulations.

This Bony Basilisk is the third creation in a series of Snap-Flex models by Mimetics 3D, and it's available for free for a limited time.

**Tolerance:**
To accommodate different printer settings and filaments, I’m uploading 3 different tolerance levels for the Bone Snake to ensure that you get the best fitting, most satisfying “SNAP” with each of your prints.

This is the **Loose** tolerance model.  For the other tolerances, please check out the other versions of the model below:

**Tight Tolerance Extra Long Bony Basilisk:**
https://than.gs/m/942802
**Medium Tolerance Extra Long Bony Basilisk:**
https://than.gs/m/942873

Please try out each to see what works best for you, and let me know which version you prefer!


Make sure to revisit us frequently for more thrilling Snap-Flex models to come. We're eager to hear your feedback and collaborate on refining this model going forward.

This model is for personal use only. If you're interested in selling physical prints of this model, please subscribe to the Mimetics 3D Commercial Tier on Thangs.

**Print Settings:**
0.2mm Layer Height
3 Wall Loops
3 Top Shell Layers
No Supports, Print-In-Place at 100% scale.  Going any smaller may disable the Snap-Flex joint.

These tolerances are TIGHT and you'll likely have to snap each segment a few times before it's loose enough to snap/unsnap easily. I recommend you use regular PLA or PLA+. ABS might be even better, but I haven't tried it yet.

Silk PLA is a bit softer and may not click as nicely. I'd also be more concerned about silk PLA holding up to the wear and tear.
If you print this in resin, please let me know how it turns out. I imagine you would need a more flexible/less stiff resin for it to work appropriately.

**Print-In-Place, No Supports, Articulating Fidget Toy**

**Subscribe To the [Mimetics 3D Commercial Tier on Thangs.](https://than.gs/u/934587?plans=true) for rights to sell prints of your cool new friend.**

**Find the Bony Basilisk's magical little feline friend over here:** https://than.gs/m/940296

Emerging from the crypts and cursed castles, the Bony Basilisk is here to bewitch and bedazzle just in time for the spooky season! With its detailed skeletal structure, this bony behemoth is prepared to perch on your shelf as the haunting highlight of your Halloween assembly or stand sentinel, casting a bone-chilling shadow for your guests.  This ancient creature refuses to let the ghosts, ghouls, and dragons have all the fall-time fun on their own.


This Bony Basilisk is the third creation in a series of Snap-Flex models by Mimetics 3D, and it's available for free for a limited time.

**Snap-Flex Collection:**
This articulated fidget toy integrates the Mimetics 3D "Snap-Flex" joint. This allows it to both move smoothly, mimicking the fluid motion of living creatures, AND stabilize in a firm pose, providing a premium fidgeting experience. 

Each **SNAP** will resonate as a symphony of satisfaction to your ears, confirming your masterful manipulations.

**Snap-Flex Instructions:**
To Lock: Push Body Segments together
To Unlock: Pull Body Segments Apart



**Tolerance:**
To accommodate different printer settings and filaments, I’m uploading 3 different tolerance levels for the Bone Snake to ensure that you get the best fitting, most satisfying “SNAP” with each of your prints.

This is the **Loose** tolerance model.  For the other tolerances, please check out the other versions of the model below:

**Tight Tolerance Long Bony Basilisk:**
https://than.gs/m/936921
**Medium Tolerance Long Bony Basilisk:**
https://than.gs/m/937050

Please try out each to see what works best for you, and let me know which version you prefer!

**Other Models:**

If you like this Bony Basilisk, be sure to check out the latest articulated model here:
**Tight Tolerance Cold Snap:**
https://than.gs/m/960229
**Medium Tolerance Cold Snap:**
https://than.gs/m/960234
**Loose Tolerance Cold Snap:**
https://than.gs/m/960235


Make sure to revisit us frequently for more thrilling Snap-Flex models to come. We're eager to hear your feedback and collaborate on refining this model going forward.

This model is for personal use only. If you're interested in selling physical prints of this model, please subscribe to the [Mimetics 3D Commercial Tier on Thangs.](https://than.gs/u/934587?plans=true)

**Print Settings:**
0.2mm Layer Height
3 Wall Loops
3 Top Shell Layers
Brim Suggested

**Suggested Material: PLA or PLA+**
**Note:** Silk PLA is too weak to hold up to repeated use of the Snap-Flex joint.  Use silks at your own risk


**No Supports, Print-In-Place at 100% scale** 
Printing any smaller may disable the Snap-Flex joint.

Printing larger than 100% will make the snap louder AND **harder to pop**, so be sure to do a shorter test print to make sure it's not **TOO hard to snap into place.**

These tolerances are TIGHT and you'll likely have to snap each segment a few times before it's loose enough to snap/unsnap easily. I recommend you use regular PLA or PLA+. ABS might be even better, but I haven't tried it yet.

If you print this in resin, please let me know how it turns out. I imagine you would need a more flexible/less stiff resin for it to work appropriately.

Long Bony Basilisk - Articulated Snap-Flex Fidget (Loose Joints)

**Print-In-Place, No Supports, Articulating Fidget Toy**

Emerging from the crypts and cursed castles, the Bony Basilisk is here to bewitch and bedazzle just in time for the spooky season! With its detailed skeletal structure, this bony behemoth is prepared to perch on your shelf as the haunting highlight of your Halloween assembly or stand sentinel, casting a bone-chilling shadow for your guests.  This ancient creature refuses to let the ghosts, ghouls, and dragons have all the fall-time fun on their own.

This articulated fidget toy integrates the Mimetics 3D "Snap-Flex" joint. This allows the Bony Basilisk to both move smoothly, mimicking the fluid motion of living creatures, AND stabilize in a firm pose, providing a premium fidgeting experience. Each **SNAP** will resonate as a symphony of satisfaction to your ears, confirming your masterful manipulations.

This Bony Basilisk is the third creation in a series of Snap-Flex models by Mimetics 3D, and it's available for free for a limited time.


**Tolerance:**
To accommodate different printer settings and filaments, I’m uploading 3 different tolerance levels for the Bone Snake to ensure that you get the best fitting, most satisfying “SNAP” with each of your prints.

This is the **Loose** tolerance model.  For the other tolerances, please check out the other versions of the model below:

**Tight Tolerance Long Bony Basilisk:**
https://than.gs/m/936921
**Medium Tolerance Long Bony Basilisk:**
https://than.gs/m/937050

Please try out each to see what works best for you, and let me know which version you prefer!

**Other Models:**
If you like the Long Bony Basilisk, be sure to check out it’s cute younger sibling, the Short Bony Basilisk:

**Tight Tolerance Short Bony Basilisk:**
https://than.gs/m/936954
**Medium Tolerance Short Bony Basilisk:**
https://than.gs/m/937047
**Loose Tolerance Short Bony Basilisk:**
https://than.gs/m/937048

Make sure to revisit us frequently for more thrilling Snap-Flex models to come. We're eager to hear your feedback and collaborate on refining this model going forward.

This model is for personal use only. If you're interested in selling physical prints of this model, please subscribe to the Mimetics 3D Commercial Tier on Thangs.

**Print Settings:**
0.2mm Layer Height
3 Wall Loops
3 Top Shell Layers
No Supports, Print-In-Place at 100% scale.  Going any smaller may disable the Snap-Flex joint.

These tolerances are TIGHT and you'll likely have to snap each segment a few times before it's loose enough to snap/unsnap easily. I recommend you use regular PLA or PLA+. ABS might be even better, but I haven't tried it yet.

Silk PLA is a bit softer and may not click as nicely. I'd also be more concerned about silk PLA holding up to the wear and tear.
If you print this in resin, please let me know how it turns out. I imagine you would need a more flexible/less stiff resin for it to work appropriately.

License: Attribution-NonCommercial-NoDerivs
CC BY-NC-ND

----------------------------------------------------------


Demon Skull


----------------------------------------------------------
If print some of my models please tag me on social media.

www.Twitter.com/carmelo_nazario
www.instagram.com/thecreatorx3d

If you want to help a brother out please consider signing up to my patreon.

www.patreon.com/thecreatorx3d

KEEP ON PRINTING!!

DEMON SKULL

Tag me on those awesome photo prints on twitter- https://twitter.com/carmelo_nazario

KEEP ON PRINTING!!

skull

Most Popular of All Time

Categories

Popular

Personalize

Trending