BLOOM CLIPS | MAGNETIC FLOWER WITH PETAL CLIPS

BLOOM CLIPS - CLIP - 2.STL

The Rail - Hook Attachment

Hook Attachment.stl

The Rail - Coat Hook

Hook Left.stl

EZPZ Pegboard Hook // 10mm Hook Type B

An excellent hook for all your pegboarding needs! This EZPZ pegboard hook prints quickly without supports, and features a unique clipping system that snaps onto your pegboard so it won't accidentally fall out, but it can also be removed in a non-destructive manner!

This particular hook has a 10mm depth and a shallow angle. You can check out my other hooks for different sizes, or leave a comment to request something specific!

---

**_Printing Guidelines_**

Print solid. That's it!

The footprint is quite small, so make sure you have a well leveled build plate and good adhesion. You may need to slow down your first layer speed or even add a brim if you're having trouble getting the prints to stay down.

---

**_Operating Instructions_**

These are designed for standard pegboards with 0.25" holes spaced 1" apart, and roughly 0.25" thick.

To install, first insert the top peg, then pop in the bottom clip. You can press the clip from below while inserting if you have a fragile pegboard.

To remove, just to the reverse, pressing from below so the clip can be removed. You can use a flathead screwdriver to press the clip up further, especially if you have a fragile pegboard.

Two part Carabiner - BackToSchool - H4/H4L

Final carabiner.stl

EZPZ Headphone Hanger (Under Desk)

EZPZ_UnderDeskHeadphoneHanger_4mmFlatHead.stl

Hooks (for IKEA Skadis Pegboard)

Hooks.3mf

GridControl - Wall Control to Gridfinity Hooks

3_Deep_6_Wide_Hooks.3mf

EZPZ Small Shelf Hook // Type1

EZPZShelfHook_Type1_Small_Hook.stl

A Most Minimal Wall Hook

wallhook-body.STL

Tough Little Hook // Peg Anything

I made stronger hooks that use two pegs to prevent rotation. At 100% infill these little suckers can hold a fair amount of weight!

Made for standard pegboard with 1/4" holes spaced 1" apart. Photographed model printed with [MatterHacker White PRO Series PLA](https://bit.ly/PRO-PLA)

Wire Shelf Hooks / Hangers

Wire_Shelf_Hook-Med.stl

Camel Hook (Medium)

Multiboard Bolt Locked 135deg Double Hook 50-90mm.stl

Bolt Locked 135deg Double Hook 50-90mm.stl

EZPZ Pegboard Hook // 10mm Hook

An excellent hook for all your pegboarding needs! This EZPZ pegboard hook prints quickly without supports, and features a unique clipping system that snaps onto your pegboard so it won't accidentally fall out, but it can also be removed in a non-destructive manner!

This particular hook has a 10mm depth. You can check out my other hooks for different sizes, or leave a comment to request something specific!

---

**_Printing Guidelines_**

Print solid. That's it!

The footprint is quite small, so make sure you have a well leveled build plate and good adhesion. You may need to slow down your first layer speed or even add a brim if you're having trouble getting the prints to stay down.

---

**_Operating Instructions_**

These are designed for standard pegboards with 0.25" holes spaced 1" apart, and roughly 0.25" thick.

To install, first insert the top peg, then pop in the bottom clip. You can press the clip from below while inserting if you have a fragile pegboard.

To remove, just to the reverse, pressing from below so the clip can be removed. You can use a flathead screwdriver to press the clip up further, especially if you have a fragile pegboard.

Coathanger S-Hook

S_Hook_35mm.stl

Printy Panel Hooks (Small - Medium - Large)

PrintyPanel_Hook_LG.stl

WPM Accessory - Folding Hooks

WPM Acc Folding Hooks 1v00a main.stl

Towel hanger

Let’s be honest, who is really taking the time to spread out a kitchen towel tidy over a bar? And If you are using a hook - it is often a struggle to find the loop and the towel is probably still wet after a few hours.
This simple and well working solution is a mix between the two options. Just throw the towel over and don’t worry about it not drying or falling down.
 
You can either screw or glue it onto your wall or cabinet. There are various glue or tape products for wall fixation out there. I used 3M Tape.

Diameter of the two screw holes: 5,5mm

Size: ca 175 × 75 × 50 mm
Don't forget to post your makes!

**Print settings**
Required build volume: 180 x 180 x 60 mm
Material usage: 40g
Print time: 4h – 5h

Material: PLA
Print direction: stls are rotated correctly, check images
Support: none
Nozzle size: 0,4 mm
Line width: 0,4 mm
Layer height 0,2 mm – 0,28 mm
Outer walls: 3
Infill: 20%
Build plate adhesion type: none
If you experience any problems, please feel free to contact me on twitter or Instagram

Camel Hook X-Smal

X-Small Wire Rack/ Shelf Hooks / Hangers.
Camel Hooks have humps, those humps have purpose, humps hold more infill, humps make you strong like bull!

Hooks

Most Popular of All Time

Categories

Popular

Trending

Popular

Paid

Videos

New Uploads

Downloads

Trending

Popular

Paid

Videos

New Uploads

Downloads

BLOOM CLIPS | MAGNETIC FLOWER WITH PETAL CLIPS

The Rail - Hook Attachment

The Rail - Coat Hook

EZPZ Pegboard Hook // 10mm Hook Type B

Two part Carabiner - BackToSchool - H4/H4L

EZPZ Headphone Hanger (Under Desk)

Hooks (for IKEA Skadis Pegboard)

GridControl - Wall Control to Gridfinity Hooks

EZPZ Small Shelf Hook // Type1

A Most Minimal Wall Hook

Tough Little Hook // Peg Anything

Wire Shelf Hooks / Hangers

Camel Hook (Medium)

Multiboard Bolt Locked 135deg Double Hook 50-90mm.stl

EZPZ Pegboard Hook // 10mm Hook

Coathanger S-Hook

Printy Panel Hooks (Small - Medium - Large)

WPM Accessory - Folding Hooks

Towel hanger

Camel Hook X-Smal