Wall Mounted Dual Filament Holder

Dual Filament Holder - Wall Mount.stl

Shelf Brackets with Filament Spool Holder Mount!

Shelf_Brackets_V1.step

Mutliboard Filament Spool Holder

SpoolHolder_v012.step

A Sturdy Simple Spool Holder

simplespool-legs-1.stl

Filament Spool Holder for the Ender 3

Spool Turned Cap 001.stl

Ender 3 Filament Spool Holder - Fully printable upgrade

Ender 3 Filament Spool Holder - Master.stl

Modular Spool holder

Spoolholder-triangle female.stl

Universal Spool Clip (Filament 1.75 mm)

clip.stl

Bambu X1 & P1P - Side Filament Holder /w P4-M10 Thread

filament  Arm 2 - Curved.stl

Ender 3 Filament Spool Retainer

This cap clips onto the spool holder to prevent spools from somehow finding their way off of the holder and onto the print bed.  I didn't think this was an issue but alas the ender has proved me wrong lol.  The outer diameter of this thing is just big enough that no spool should be able to make it over.  

Sturdy Simple Top Loading Spool Holder

simplespool-top.stl

Honeycomb Spool Holder

This simple spool holder is made to sit beside your 3D printer so that you do not need to rely on the original spool holder the printer comes with. It is meant for most (inner hole of spool must be 43mm or larger to fit) spools of filament 1kg or less. It has a modern aesthetic that culminates with the hexagonal pattern on its side wall.

5k spool holder stand up 

stand up 5k spool holder v4.stl

K1 Max - Riser - SideSpool - Bowden extend clips

K1 Max Lid Riser for side spool.stl

Filament Roller Support

SpoolSupportPartA1.stl

1, 3 & 5 kg metal shelf and rack mounted spool holder vertical above head assembly

MULTI SPOOL HOLDER.step

Kingroon KP5L Spool sensor top mount

I was tired of my spool being on the table so I designed this, this is my 2nd design ever and I just wanted something that worked, with out needing other hardware.

I just unscrewed A z screw bracket and 1 side of the z axis and slid it on and it sits nicely.

Show me your remixes so i can get new ideas..

I printed with 15% infill and supports for build plate only.

Bambu Lab Filament pulley for carbon x1

Change the direction of the filament to guide it into the machine in a gentle way, placing the spool it a better orientation.

Recommended Material and settings:

PETG – dark color
Bottom and top layer 1.4mm 7 layers
5 layer wall thickness
Gryoid infill at least 15%
Plate: textured PEI plate with glue only on the parts for the calibration extrusions. No brim required.
Order of inner wall/ outer wall/ infill: infill, outside, inside or outside, infill, inside (i’ve switch to the former for most prints but I think I did particular machine with the later, I made this a few months ago and don’t remember, good luck)

Hardware Required
608 sized bearing
Super (cyanoacrylate) glue
1 Meter Bowden Tube

Assembly:
Press bearing into pulley, the glue flange over bearing – dark PETG colors glue better than light colors
Put assembled bearing onto spindle, place bracket over spindle and bracket locator, screw short screw into bracket locator – snug plus tightness is good enough

Insert new bowden tube into printer, the new tube only needs to be and inch or two longer, I recommend cutting it after you have the assembly somewhat located.

place assembly over filament spool holder, insert bowden tube into assembly, sticking out about an inch past it’s place of securing towards the pulley. Enough that the tube can flex a bit as the filament will move around a bit. 

Ensure the bowden tube is graceful in its curving into the machine (to test you can push filament through the tube to test it’s ease of insertion), once satisfied place the threaded block on the underside of the machine and the longer screw through the assembly into the block. Tighten snug plus.

If you don’t know how to use the device at this point you should now have profound feelings of everlasting shame and may whatever deity you worship have mercy upon your wretched soul. 


Other notes:

The bracket is strong enough to pull the bowden tube tight, pick up a full spool of tangled filament, the dry box it is in,  and all your frustrations at a failed print (I wouldn’t know, that’s just what a friend told me) without noticing. 

90 deg connector for 25mmpipe .obj

90 deg connector for 25mmpipe for 3d printing filament holder. you must print 1 piece

holder v20.step

filament holder step file for 2 filament roles 1kg and 1/2kg

Filament Holder

Most Popular of All Time

Categories

Popular

Trending

Popular

Paid

Videos

New Uploads

Downloads

Trending

Popular

Paid

Videos

New Uploads

Downloads

Wall Mounted Dual Filament Holder

Shelf Brackets with Filament Spool Holder Mount!

Mutliboard Filament Spool Holder

A Sturdy Simple Spool Holder

Filament Spool Holder for the Ender 3

Ender 3 Filament Spool Holder - Fully printable upgrade

Modular Spool holder

Universal Spool Clip (Filament 1.75 mm)

Bambu X1 & P1P - Side Filament Holder /w P4-M10 Thread

Ender 3 Filament Spool Retainer

Sturdy Simple Top Loading Spool Holder

Honeycomb Spool Holder

5k spool holder stand up

K1 Max - Riser - SideSpool - Bowden extend clips

Filament Roller Support

1, 3 & 5 kg metal shelf and rack mounted spool holder vertical above head assembly

Kingroon KP5L Spool sensor top mount

Bambu Lab Filament pulley for carbon x1

90 deg connector for 25mmpipe .obj

holder v20.step