This is a remix of the Gridfinity Modular Drawer System that fits onto the Multibpard. I created a Peg with a slider on it and added slots to the back of the Gridfinity MDS so it can slide on and off the pegs easily. 

Gridfinity MDS Remix for Multiboard

Gridfinity-Modular-Case.3mf

This is designed to hold an aerosol can, canned air, etc. on your multiboard. It is attached via the overly strong pegboard clips and holds the cans at an angle. Two different models are provided, one with built-in support and one without if you'd like to add your own. It should be printed on the side to provide the most strength for the pegboard clips. The model is not oriented this way. The pre-supported model may have the slightest of sagging at the top of the cylinder but will print successfully on a Creality K1. To remove the supports around the pegs, use your side cutters to gently separate the supports from the pegs. It requires three horizontal pegboard spaces to clip in and is designed so you can butt them up horizontally to store multiple cans with no gaps in between (see pictures). Correct vertical spacing will have three open peg board holes between two of these holders.  There is a small triangular hole in the model for any spray nozzles your can's may have. Interior diameter is ~66mm and fits most air cans and US spray cans. There is a .STEP file in the download.

Multiboard Aerosol Can Holder Pegboard Attachment

MultiBoardCannedAir_NoSupports.stl

MultiBoardCannedAirSupports.stl

After hanging a few of these, I quickly realized the end nut was overkill and could be replaced with a hole in the bottom of the brace. I initially had other ideas where the nut may have provided value, but scrapped them during design.

I wanted to store my many rolls of tape on the wall, so I designed a Tape Roll Holder for the Multiboard Storage System.
Items needed
Multiboard Tape Roll Storage Rack - 3D Printed (at least two, more, the longer you go).
1/2" diameter PVC Pipe from your local hardware store
Small Screw to Hold Pipe Nut in place
13 mm Big Thread, Flat Head, T-Bolt (2 per brace) from "Keep Making."

Designed to be printed on its side. Does not require support.

Multiboard Tape Roll Storage Rack

Multiboard Tape Roll Storage Rack.stl

A Simple holder for the Dremel Lite on the Multiboard

Dremel Lite Holder for Multiboard

Dremel-Holder.stl

This will allow you to mount your harbor freight glove box to the multiboard.  I have tested the horizontal pieces and they work great.  I have not tested the vertical but it's just a slight modification to the horizontal.

You will need x2 of the horizontal mounts and x2 multiboard snaps.  If you wish to mount your gloves vertically you will need x1 of the horizontal mount, x1 of the vertical, and x2 of the multiboard snaps. 

If this doesn't make any sense to you, I would encourage you to visit https://www.multiboard.io/

Harbor Freight Glove Box for Multiboard

HF Glove Box Multiboard.stl

A Multiboard|Pegboard hanger for crimpers and pliers

Multiboard | Crimper | Plier | Pegboard

Peg Crimper 55x25.stl

Store 2 pairs of scissors on your Multiboard so they're always within arm's reach.

Print upside down with no supports at 0.2mm layer height with three walls for optimal strength.
Requires 2 "9 mm Small Thread, Plain Head, T-Bolt" to mount to your Multiboard, which may be obtained from "Keep Making" on Thangs.

Multiboard Dual Scissor Holder

Multiboard Dual Scissor Holder.stl

**!!UPDATED VERSION!!**
I have made a simple but important update to the Multiboard Bolt Driver:  The depth of the socket has doubled so there is less slipping when driving bolts.  note:  Ignore V2 as that was an error in uploading the model with my 4D brand.  V3 is the updated, brandless version.

**Updated slicer settings**
I confirmed that although printing this horizontally is the correct orientation for toughness, it requires a substantial support which ruins the texture of one side of the driver and results in a rough edge.  Additionally, if you do not add supports to the socket, it will sag and will therefore be unusable - ask me how I know.

Standard 0.2mm except:
4 Wall Line Count - Increases sturdiness
10% Infill - results in a lighter weight driver
10mm Brim - Not required but I was more comfortable printing vertically with a brim

This is a remix of "Screw Driver" by megatron321

( https://www.thingiverse.com/thing:709811 )

This screw driver has been adapted to drive MULTIBOARD bolts and T-Bolts.  After installing and removing so many multiboard bolts, my fingers hurt terribly so I created a tool to easily install and remove the bolts.  It is designed to fit both plain and flat bolts as well as plain and flat t-bolts.

I added grooves along the head to indicate the sides of the bolts to assist with lining them up with the multiboard tiles.  There are two smaller grooves that indicate the top/bottom points of the t-bolts.

I added a custom brand to the handle base. The file does not have the brand.

It fits perfectly in a Multiboard Horizontal Pole Mount when attached to my Multiboard Multitool Holder.

Multiboard Bolt Driver

This is a remix of "Screw Driver" by megatron321

( https://www.thingiverse.com/thing:709811 )

0.2mm quality
No supports needed if printed vertically

This screw driver has been adapted to drive MULTIBOARD bolts and T-Bolts.  After installing and removing so many multiboard bolts, my fingers hurt terribly so I created a tool to easily install and remove the bolts.  It is designed to fit both plain and flat bolts as well as plain and flat t-bolts.

I added grooves along the head to indicate the sides of the bolts to assist with lining them up with the multiboard tiles.  There are two smaller grooves that indicate the top/bottom points of the t-bolts.

I added a custom brand to the handle base. The file does not have the brand.

I printed this standing up on the base and used a Brim to keep it in place. If you want to deal with more supports, you can print it in its side so the layer lines are perpendicular to the torque direction but I haven't had any structural issues.

MultiBoardDriver_v2.stl

Looking for your tape measure again?

Having your tape measure on your Multiboard, you'll never spend time looking for your tape measure again.
Better yet, put a Multiboard up in every room with tape measures on each so one will always be within arms reach.

Print upright with no supports at 0.2mm layer height with three walls for optimal strength.
Requires 2 "9 mm Small Thread, Plain Head, T-Bolt" to mount to your Multiboard, which may be obtained from "Keep Making" on Thangs.

Multiboard Tape Measure Storage Clip

Multiboard Tape Measure Storage Clip.stl

Remixed from the "HSW Angled Drill Holder" by kstuken on Printables.com - https://www.printables.com/model/498594.  All I did was move the holes to accommodate Mutliboard snaps.  I only remixed the wider of the two mounts from the original.
The first version requires M3 screws about 14mm-16mm long and M3 Hexnuts required for assembly, as well as multiboard snap, of course.
On 2024-02-19 I added a version which should work with Small-thread T-bolts as suggested by spikeon in the comments.

Multiboard Angled Drill Holder

Remixed from the "HSW Angled Drill Holder" by kstuken on Printables.com - https://www.printables.com/model/498594.  All I did was move the holes to accommodate Mutliboard snaps.  I only remixed the wider of the two mounts from the original.
M3 screws about 14mm-16mm long and M3 Hexnuts required for assembly.

Quick design for a bracket to hold the Creality supplied blue snips on a Multiboard from Keep Making, Zack Freedman.  Requires a push-fit bolt or snap.

Printed with .2 layer height, 15% infill, 3 top/bottom layers, 3 perimeters/walls.  If tight change horizontal expansion to -.02.

Snips Bracket for Multiboard

Multiboard Snips Bracket.stl

Multiboard Remixes

Activity related to collaborating with others on models

Likes, comments, and activity from your community

New content from your premium memberships

Emails and messages from designers you follow

Get notified when someone purchases your models or memberships

jlmeredith

Achievements

Voyager

Seedling