**Manage your Galileo 2 Cables SECURELY!**
 
Recently I installed the Galileo 2 Extruder assembly on my Voron 2.4, but I had an issue mounting my CAN Umbilical cable. The files for the G2E include a PG7 mount, but it mounts behind the Extruder Motor. On a Voron 2.4 this means it hits the Z-Cable Chain & in my case, my Umbilical Mount on the rear Gantry. It seems to be made for Tridents with the cable going through the vent opening only. So I made this mount! It mounts to the left of the Extruder motor and provides a clean back that has no interference issues with the existing Voron Design V2.4 parts. 

Files include 2 versions of both a PG7 mount and a M12x1.25mm Mount. One version is standard design, the other has a slot so you don't have to feed your umbilical cable through the mount. I needed this so I could easily swap my cable setup without having to rewire my entire CAN cable & resleeve it. The “Split” versions use a single M3x12 screw to add some rigidity to the opening after you install your wire & cable gland.

This design also uses a 20mm spacer design (the HartK one used 17mm), which should allow just enough room to fit a wire or two between the motor & the mount. I've included a 20mm printable standoff, but I really recommend aluminum stand-offs, easily available on Amazon and from Hobby Shops (common in RC stuff).

**NOTE:** As this mounts to the motor mounting screws, and the Galileo 2 has a "floating" motor design, this MAY cause some tensioning issues if your umbilical does not have enough slack. Be mindful of how much tension is on your umbilical cable when assembling! I haven't had any issues yet, but I could see it being a problem if the cable is pulling tightly.

---------------------------------------------------------------
**Parts (Affiliate Links):**
- [LDO Galileo 2 Kit](https://collabs.shop/wesugy)
- [M3 Hardware](https://amzn.to/3u0JyI2)
- [M3 Stand-Offs](https://amzn.to/3u7V0S0)
- [PG7 Cable Gland](https://amzn.to/3HA7SDF)
- [Polymaker Filament](https://tinyurl.com/Polymakerr)
- [LDO Voron 2.4 Kit](https://collabs.shop/uskpm1)
- [BigTreeTech SB2209 CAN](https://shrsl.com/4e6do)
---------------------------------------------------------------
 **Files Included:**
- G2E Cable Glands – STEP 
- G2E PG7 Mount STL 
- G2E PG7 Split Mount STL 
- G2E M12 Mount STL
- G2E M12 Split Mount STL
---------------------------------------------------------------
**Recommended Print Settings:**
- .2mm Layer Height
- 3 Perimeters 
- 40% Infill
- No Supports Required
- ABS or ASA Filament
---------------------------------------------------------------
Want to Support what I do? Check out my social medias please!

**Link Tree:** http://www.MandicReally.com/links
---------------------------------------------------------------

Please consider supporting my work by becoming a Patron on Patreon: [MandicReally Patreon](https://www.Patreon.com/MandicReally)

Galileo 2 PG7 Cable Gland Mount - FITS Voron 2.4! M12 too!

G2E_PG7_M12_Cable_Glands_V4.step

Remix of Modbots organizer to add more drawers. Please give him the credit.
https://thangs.com/Modbot/Voron-01-Hardware-Organizer-23915

Three different size choices:
Small extension with 24 drawers
Large extension with 28 drawers
Extra large extension with 28 drawers, 4 of which are doublewide.

The small extension can print on a 200mm buildplate (Prusa mk3) and the large can barely squeeze onto a 235mm plate (Ender 3). The largest will need a build volume of 265mm.

I added additional magnet slots in the top which are optional and a small retaining square more for visual reference than anything. The 24 drawer is just enough to fit the voron 2.4 hardware kit.

Voron Hardware Organizer EXTENDED REMIX

Remix of Modbots organizer to add more drawers. Please give him the credit.
https://thangs.com/Modbot/Voron-01-Hardware-Organizer-23915

Three different size choices:
Small extension with 24 drawers
Large extension with 28 drawers
Large extension with 28 drawers, 4 of which are doublewide.

The small extension can print on a 200mm buildplate (Prusa mk3) and the large can barely squeeze onto a 235mm plate (Ender 3). The largest will need a larger build volume of 265mm.

I added additional magnet slots in the top which are optional and a small retaining square more for visual reference than anything. The 24 drawer is just enough to fit the voron 2.4 hardware kit.

Voron 0.1 Hardware Organizer extended wide drawers.STL

**Solid State Voron!** 

Boot Klipper from a SSD with this mounting setup! Designed to used in conjunction with one of the existing DIN Rail Mounting Clips from the Voron Design files.  This mounts a standard 2.5" SATA SSD to a DIN rail in a Voron (or other 3d printer / machine). Use this combined with a SATA to USB cable to boot your Klipper instance off a much more reliable SSD! 

Also includes a SSD Clip to ensure the SATA to USB adapter cannot fall off accidentally!

Video explanation here: 

Parts Used (Affiliate Links):
Parts used (affiliate links):
*** Sata USB Cable: https://amzn.to/3HNG2VO
*** Screws: https://amzn.to/3WAzr5o
*** SSD: https://amzn.to/3FMxnAt
*** Raspberry Pi 4: https://amzn.to/3GhGElz

---------------------------------------------------

**INCLUDED FILES:**
- Voron DIN Rail SSD Mount - STEP File
- Voron DIN Rail SSD Mount - STL File
- SSD Clip
------------------------------------------------------
**PRINT PARAMETERS:**
- No support required
- 20% Infill
- .2mm layer height
- .45mm Extrusion Width

I printed mine with [Polymaker ASA](https://tinyurl.com/PolymakerASA) _(Affiliate Link)_
-------------------------------------------------------
Want to Support what I do? Check out my social medias please!

Link Tree: http://www.MandicReally.com/links
-------------------------------------------------------

Design covered by GPL3 Open Source license. Any Remixes or Derivatives are required to adhere to license terms & use the same license.

PLEASE Attrubute any Remixes of my designs: MandicReally

Voron DIN Rail SSD Mount

Voron_DIN_SSD_Mount_V1.step

SSD_USB_Retainer_Clip_V1.stl

Voron

Activity related to collaborating with others on models

Likes, comments, and activity from your community

New content from your premium memberships

Emails and messages from designers you follow

Get notified when someone purchases your models or memberships

jackerhack

Achievements

Voyager

Voron

Galileo 2 PG7 Cable Gland Mount - FITS Voron 2.4! M12 too!

Voron Hardware Organizer EXTENDED REMIX

Voron DIN Rail SSD Mount