Would it not be cool to have an adapter part for the horizontal rail to fit on a vertical rail. This adapter part could have predrilled holes on the side to screw in the horizontal dowels to prevent them from sliding out. Then I could use two tripod vertical rails and have a horizontal rail I can put anywhere in a room not just on a wall.
I third this! would love to connect two vertical wall hangers on either side of a window to a horizontal wall hanger that ran in front of the window. OR..... two tripod planters with a horizontal between them. thanks for the awesome stuff!
I want the horizontal-vertical connection as well! For me it would be wallmounted though. So I am hoping for a deeper wall connector and a vertical-horizontal mounting solution to connect horizontal to vertical and vice-versa!
Is the new bridge flow setting for drip trays something I should be changing on all pots? I'm curious if this helps improve the snug fit of the drip tray? Thanks man!
Saw this on a facebook reel and now we're planning on redoing the kitchen because we love this so much! What width dowel did you use in the photo? Like is it 4ft, 6ft, etc.? I know we can do whatever we want, but I like the spacing you have on that photo.
Awesome! I used a 36" dowel but like you said, you can use whatever size you want. 36" dowels are just the most common at hardware stores. If you decide to go any longer than 4ft, you might want to use an additional middle mount to ease the load on a wider span.
I am printing this now, you think theirs a way you could add in the middle a scalable height pendant light so we have a nice light mount? Almost a complete design with this
Yes! I have tons of attachments coming for this one. Also, I just noticed an issue with the middle wall mount. If you're printing that part, I'd cancel that object. The files are updated now so you can redownload and print the fixed middle mount.
Yeah the middle mount can print fine without supports but feel free to use them if you feel like you need them. Round holes don't usually print very well in a vertical orientation but the insides of them are hidden by the dowels so I wasn't worried about it.
So ive printed some of the pots and dovetail attachments and they dont slide together very easily is there a setting change you think is needed to help that tolerance?
Very excited about this print, and your work looks amazing. After downloading the files, and importing the files into Orca Slicer for my FlashForge Adventurer 5M, I'm seeing a ton of errors. I'm also very new to 3D printing, so hoping it is something easy. A quick search is telling me that the files are written specifically for Bambu Studio, and may be the reason for the errors. Any advice for FlashForge users?
so i just printed a system and i love it. but i put mine across a window. and because of this the back wasnt deep enough( i ran into the window frame. i ended up gluing a piece of wood to the back but not the best. i cant just extend it due to the hole sizes. Would you think about making a spacer that would go in the back. would be 1/2 inch think and had a thru hole on the keyhole? then you could just print as many spacers as needed and not have to change the file!
hi i was just wondering if there's any particular reason why you didn't use PETG filament for this? i'm planning on printing with PETG but just wanted to be sure before doing so. thank you
This is awesome! Would it be possible to make another wall mount piece that has a hook attached to it? Like the add on coat hook, but built into the mounting piece? Just a thought. Thanks!
Discussions — The Horizontal Rail
Would I be able to put Ira planters on this? Looks like yes to me but just to confirm. Thanks!
Would it not be cool to have an adapter part for the horizontal rail to fit on a vertical rail. This adapter part could have predrilled holes on the side to screw in the horizontal dowels to prevent them from sliding out. Then I could use two tripod vertical rails and have a horizontal rail I can put anywhere in a room not just on a wall.
I third this! would love to connect two vertical wall hangers on either side of a window to a horizontal wall hanger that ran in front of the window. OR..... two tripod planters with a horizontal between them. thanks for the awesome stuff!
I want the horizontal-vertical connection as well! For me it would be wallmounted though. So I am hoping for a deeper wall connector and a vertical-horizontal mounting solution to connect horizontal to vertical and vice-versa!
This would be so cool with dovetail connectors on each end so it could be connected onto two normal rails!
Is the new bridge flow setting for drip trays something I should be changing on all pots? I'm curious if this helps improve the snug fit of the drip tray? Thanks man!
Saw this on a facebook reel and now we're planning on redoing the kitchen because we love this so much! What width dowel did you use in the photo? Like is it 4ft, 6ft, etc.? I know we can do whatever we want, but I like the spacing you have on that photo.
Awesome! I used a 36" dowel but like you said, you can use whatever size you want. 36" dowels are just the most common at hardware stores. If you decide to go any longer than 4ft, you might want to use an additional middle mount to ease the load on a wider span.
I am printing this now, you think theirs a way you could add in the middle a scalable height pendant light so we have a nice light mount? Almost a complete design with this
Yes! I have tons of attachments coming for this one. Also, I just noticed an issue with the middle wall mount. If you're printing that part, I'd cancel that object. The files are updated now so you can redownload and print the fixed middle mount.
the middle part printed okay with exception to the round holes the top side of them almost seems to need support. ill redownload
Yeah the middle mount can print fine without supports but feel free to use them if you feel like you need them. Round holes don't usually print very well in a vertical orientation but the insides of them are hidden by the dowels so I wasn't worried about it.
it turned out awesome, ide love to see a light mount for this as your vertical rail one is awesome thank you
So ive printed some of the pots and dovetail attachments and they dont slide together very easily is there a setting change you think is needed to help that tolerance?
What printer are you using? Did you use the 3mf with the preloaded settings or did you import the STLs into your slicer yourself?
Just loaded the 3mf and realized it changed settings so I will retry the print now.
I imported them into the slicer, cr10 pro, I guess I didnt know there was a diff
Would be great to have an option for a 3/4" dowel rod as well. I already have a bunch of those and would be nice to re-use them.
I'd like to see the wall mount options for 3M Command Strips vs. screws added to the mix.
bambu labs is giving me a floating cantilever error on the 1inch wall mounts. is this something i should just ignore?
Very excited about this print, and your work looks amazing. After downloading the files, and importing the files into Orca Slicer for my FlashForge Adventurer 5M, I'm seeing a ton of errors. I'm also very new to 3D printing, so hoping it is something easy. A quick search is telling me that the files are written specifically for Bambu Studio, and may be the reason for the errors. Any advice for FlashForge users?
so i just printed a system and i love it. but i put mine across a window. and because of this the back wasnt deep enough( i ran into the window frame. i ended up gluing a piece of wood to the back but not the best. i cant just extend it due to the hole sizes. Would you think about making a spacer that would go in the back. would be 1/2 inch think and had a thru hole on the keyhole? then you could just print as many spacers as needed and not have to change the file!
hi i was just wondering if there's any particular reason why you didn't use PETG filament for this? i'm planning on printing with PETG but just wanted to be sure before doing so. thank you
I used black PETG for mine and it turned out perfect, stronger too.
This is awesome! Would it be possible to make another wall mount piece that has a hook attached to it? Like the add on coat hook, but built into the mounting piece? Just a thought. Thanks!
Anxiously awaiting a grow light attachment for this!
Printed mine in Polymaker glitter green abs on my mercury 1, came out perfect. i did some live streams of the prints @brock4629 on youtube
Do all the vertical planters fit on these?
Yep!