Our clickers work with a wide variety of switches. We have seen people have problems with the switches that have 2 outer walls around the (+) post. I would recommend trimming off the 2 outer walls, if those are the switches you are using, as the walls tend to bend outward and cause them to get stuck inside the key switch itself.
Hello, I bought a few models of clickers from your shop, and I discovered that the switches that I use are not compatible with the toys. I read the description, but I thought the Kailh switches were just a recommendation. How can I use my own switches on your clickers? Thanks
Same issue with the others. Such a headache 😢 Hope you can fix this. I already tried trimming off (literally) the plus sign. The switch just doesn't click, it gets stuck.
These came out great...but for some reason the top part of macroon(plus sign) fits but doesn't stay put. When i flip over the macroon the top part falls off.
Are you supposed to glue the key switch into the base of the macaroon? These ones don't snap in and the stem gets stuck and unable to click or utlize the spring when pressed. I had to manually remove the plastic housing right around the stem (it's not the upper housing but a plastic guard around the crossguard contact point) so it wouldn't get stuck upon pressng. But the switch itself doesn't stay in the base. It easily falls right out.
They should fit. You may need to trim off the bottom prongs or any plastic that sticks too far down. Those ones look like they have a long pointed plastic piece that could be causing the fit issues?
Can you share the suggested print settings? I'm not using a Bambu, and when I import the 3mf but change the printer to my own, it changes all the settings. I'm having trouble with the area where the clicker snaps into the top, easily breaking off.
Hi! You should just be able to use stock settings. If you are having issues with the post snapping off there are a few things you can check like upping your print temperature, calibrating your filament flow rate, and increasing your cooling fan speed.
Also, if it helps, you can also download Bambu Studio and still use it for your printer. They support other branded printers too, not just Bambu printers.
Hi sorry, these do not print in place, you need to add supports on the side with the filling, There was a picture that said it was print in place and that was incorrect. Sorry about the confusion there.
Discussions — Macaron Clicker - Macaron Fidget - Ludo Food
Ok this doesn't work with generic switches. Uuggh only low profiles
Our clickers work with a wide variety of switches. We have seen people have problems with the switches that have 2 outer walls around the (+) post. I would recommend trimming off the 2 outer walls, if those are the switches you are using, as the walls tend to bend outward and cause them to get stuck inside the key switch itself.
very nice model
Thank you, I hope you enjoy it!
Hello, I bought a few models of clickers from your shop, and I discovered that the switches that I use are not compatible with the toys. I read the description, but I thought the Kailh switches were just a recommendation. How can I use my own switches on your clickers? Thanks
Hi! There are a lot of switches that fit these designs. What switches are you using?
Hello! Is there any way to get this Macaron smaller? I can't resize due to the clicker part. Thanks!
Hi, we only have the one size right now! But I can add it to a list for if we do decide to redesign anything.
Same issue with the others. Such a headache 😢 Hope you can fix this. I already tried trimming off (literally) the plus sign. The switch just doesn't click, it gets stuck.
What switches are you trying to use?
These came out great...but for some reason the top part of macroon(plus sign) fits but doesn't stay put. When i flip over the macroon the top part falls off.
If you are having fit issues for the top, you could add a small bit of glue into the post (plus sign) and it should hold more securely
Hello! Do you have a version with the "filling" / white section as a separate print file? thanks!
Hi! I do not, as it's needed where it is, for the height of the clicker to fit into it properly.
Are you supposed to glue the key switch into the base of the macaroon? These ones don't snap in and the stem gets stuck and unable to click or utlize the spring when pressed. I had to manually remove the plastic housing right around the stem (it's not the upper housing but a plastic guard around the crossguard contact point) so it wouldn't get stuck upon pressng. But the switch itself doesn't stay in the base. It easily falls right out.
https://www.amazon.com/Keyboard-Switch-Dustproof-Mechanical-Tactile-Switches/dp/B0C3H7PR1Z/ref=sr_1_1
They should fit. You may need to trim off the bottom prongs or any plastic that sticks too far down. Those ones look like they have a long pointed plastic piece that could be causing the fit issues?
Can you share the suggested print settings? I'm not using a Bambu, and when I import the 3mf but change the printer to my own, it changes all the settings. I'm having trouble with the area where the clicker snaps into the top, easily breaking off.
Hi! You should just be able to use stock settings. If you are having issues with the post snapping off there are a few things you can check like upping your print temperature, calibrating your filament flow rate, and increasing your cooling fan speed.
Also, if it helps, you can also download Bambu Studio and still use it for your printer. They support other branded printers too, not just Bambu printers.
How did you get this to print in place?
wdym?
There's no orientation that you can print these without support. So, I'm wondering how to print in place.
Hi sorry, these do not print in place, you need to add supports on the side with the filling, There was a picture that said it was print in place and that was incorrect. Sorry about the confusion there.
Thank you for clearing that up.
These are not print in place. They require supports