A simple thrust stand design made using 3/4" pvc and a slab of wood. (most) of the screws are m5, and the load cell arm uses an m3 screw.

Thrust Stand (old)

Thrust-Stand v11.stl

My take on a joystick guard which would allow you to safely put the deck in a backpack without a carrycase.

The most consistent way I got it to print well is to slice upside down (bigger side on top). This allows for better support placement on the hinge. 

Another tip Is to not take the print off the bed immediately, Instead heat the bed to the glass transition temperature of your filament (80-85c for PET-G And 55-60c for PLA). Once it has been heated for a while, remove the part while still warm and then slowly attempt to close/open the hinge. This will make the two halves open more easily while also not snapping.

Magnets used:
[5x3mm](https://www.amazon.com/Magnets-Neodymium-Magnet-Whiteboard-Kitchen/dp/B09GLWMN7N/ref=sr_1_4?crid=1J2K0A9MGQQRU&keywords=5x3+magnets&qid=1677016998&sprefix=5x3+ma%2Caps%2C100&sr=8-4)

 Print in Place Steam Deck Joystick Guard

Clip (low tolerance).stl

Guard.step

Guard.stl

Guard(v48).stl

My first ever propeller design (so its not that great). I wanted to figure out how to make a toroidal geometry in fusion 360 while also making a propeller I could test on my DJI mini 2. However unfortunately since I printed them in PETG, they seem too heavy and the motors are not able to spin them fast enough, which seems to trigger some type of safety system and the drone does not take off.

Toroidal Prop (dji mini 2)

Toroidal prop Fix.stl

Toroidal prop FIX.stl

Toroidal prop.stl

Have you ever wanted to attach a model rocket motor to a hot wheels car? Well I do, I haven't tested it yet but this is what i came up with to attach the motor to the car in the simplest way possible. 

All the screws and nuts are M3 besides the 2 used to close the rocket clamp, those are M2.5

CAD files included (I think you need to download all to see them)

Hot Wheels Rocket Motor Clamp

Car clamp bottom.stl

Car clamp top.stl

Rocket Clamp bottom.stl

Rocket Clamp top.stl

Solid Model.stl

This is a simple rod with indicators for amounts of clay and fuel to pack in a 3/4" model rocket based on a video from TKOR.

The video:
https://youtu.be/12fR9neVnS8

Rocket Packing rod

Rocket Dowel.stl

This is a magnetic attachment system for 2 macro pads I bought Recently. They are generic acrylic stack macro pads, so I figured the easiest way to do this was to print a whole bottom panel which turned out pretty nice. 

The screws used to attach the bottom plates are the same as the ones that come with the macro pad, M2 screws. And the piece that attaches to the base uses M3 screws.

The links to the hardware I used:
1. (5 key) https://a.co/d/2XaLdSH
2. (4 key) https://a.co/d/ig5yzBi
The 4 key is not exactly the one I used but similar.
3. (Magnets) https://a.co/d/ffxtwGc


Modular Keypad Base

Base.stl

Bottom Panel (4k).stl

Bottom Panel (5k).stl

Simple Basket made for rinsing my Resin prints in IPA. Uses M3 Screws

Resin Wash-basket

Handle

Basket.stl

Pi Zero 2 Case

Case Bottom

Hated my cat stepping on my power button and losing hours of work. So say hello to my 2nd CAD project.

I made this for my Lian Li Lancool II

PC Power Button Cover Lancool II

Print ready all in one.stl

Activity related to collaborating with others on models

Likes, comments, and activity from your community

A roundup of models that we think you'll like

For when we think someone might have posted your content as their own

New content from your premium memberships

Emails and messages from designers you follow

A7SUKO