A 'print in place' ratcheting spanner/wrench.

Inspired by the freewheel mechanism on a bicycle, I designed this tool to be compact and strong but most importantly it can be printed in place, already assembled.

The internal gear rotates in one direction depending on which way round the tool is engaged. 

The spring latches into place perfectly to engage when tightening but slides over the teeth when spinning the opposite way.

All parts have been designed with 3d printing in mind with no need for support material. The 45 degree angle internally not only makes this easily printable, but it also locks the turning sprocket inside the frame.


#3Dprint

Ratchet Spanner Wrench 15mm

A rotating Sharpie pen container which uses a ball bearing and spring to lock into 4 different positions.

See this in use: https://www.instagram.com/p/CSzTqfMDwXI/?utm_medium=copy_link

#DIY

Sharpie Container

internal.stl

A simple lightweight and minimalist binder for attaching multiple hole punched pieces of paper.  Designed to be more portable than a lever arched file.

For the times when you need to carry a few pieces of loose paper but you don't need to carry a full file or folder.

See this in action here: https://www.instagram.com/p/CStojX6DhWw/?utm_medium=copy_link

#DIY

Paper Binder - compact and minimal design

A simple lightweight and minimalist binder for attaching multiple hole punched pieces of paper.  Designed to be more portable than a lever arched file.

Exclusive access to Kwerkshop models. Print and sell my models with a commercial license.

Print and Sell Kwerkshop Designs

**G'day people!**

This is a multipart part Bilby kit that can be glued together and printed in different colours. The arms have an axle to allow them to pivot together. The tail is articulated and is in two parts for different colours.

This model was created as part of the Save The Bilby 3d print event by Creatrix_Brit on social media, download, print and share as many as you can to spread awareness of the endangered bilby

Parts should fit together with good tolerances but will require gluing. See images for reference.

Bilby Multipart Model Kit - Save The Bilby 

kwerkshop_bilby_arm_axle.stl

kwerkshop_bilby_arms.stl

kwerkshop_bilby_body.stl

kwerkshop_bilby_ears.stl

kwerkshop_bilby_eyes.stl

kwerkshop_bilby_nose.stl

kwerkshop_bilby_tail_a.stl

kwerkshop_bilby_tail_b.stl

Use this to give you more space for handlebar mounted cycling accessories. The design is meant to fit onto 31.8mm handlebar diameter and the accessory bar is 22.2mm diameter (suitable for most handlebar mounted accessories).

You will need: 
8x M5x20mm Bolts 
8x M5 Brass heat set knurled inserts

Printing:
I used 20% honeycomb infill and multiple walls for strength. Use a material appropriate for your requirements.
Disclaimer:
You are printing and using this at your own risk and I am not responsible for any injuries that may occur when using this item.

Handlebar Accessory Extender Bar

bar.stl

large_cap.stl

main_body.stl

small_cap.stl

Make your desk more exciting with this gorgeous and cute cat feet phone stand!
This model is scalable to your desired size but should hold most phones in portrait or landscape mode.

**Printing Instructions:**
Print with your desired layer height.
No support necessary apart from the slot where the tail goes in.
Parts are printed separately and assembled later.
Glue may be required for assembly.
Use a brim for the tail for more bed adhesion security.

**Filament in the images:**
Eryone Matte White
Sunlu Sakura Pink

Cat Feet Phone Holder - Commercial

cat_feet_phone_holder_beans_kwerkshop.stl

cat_feet_phone_holder_body_kwerkshop.stl

cat_feet_phone_holder_tail_kwerkshop

Activity related to collaborating with others on models

Likes, comments, and activity from your community

A roundup of models that we think you'll like

For when we think someone might have posted your content as their own

New content from your premium memberships

Emails and messages from designers you follow

kwerkshop