I printed this on my Bambu Lab P1S without any issues in 100% size. Default settings: 0.2 mm Standard profile. If you use a “bed slinger”, I recommend turning it 90% sideways, as the tip is the trickiest part to print.

€: As some reported tips flying out at 100% scale I added a tight tolerance version :) Printed fine for me, too! :)

Retractable Kusanagi Sword (print in place)

Kusanagi retractable v2.1.stl

This is my own flexi, print-in-place Dragon Design, which is over 1 meter (39") long.

This is a giant Crystal Dragon that has grown naturally and has engaged in battles with other Dragons. ;)

I recommend printing it at 100% scale. While 90% has been tested and confirmed, it presents a serious challenge for your build plate adhesion and printer cooling settings. 

It might be helpful to increase the build plate temperature to 60°C (for rough PEI or a Cool plate, too!) for additional adhesion.

The result is highly rewarding. Please note that this is not a toy for children as the crystals have sharp points! :)

License: 
CC BY-NC-ND 4.0 DEED
Attribution-NonCommercial-NoDerivs 4.0 International

Elder Crystal Dragon (Flexible, Print-in-Place)

Elder_Crystal_Dragon_1.0.stl

This is an easy two part print. 

Print the handle and star in the given orientation. I recommend using a semi translucent filament for the star. Support is recommended in the star to support the topmost hole layers.

You can use one of those cheap LED tea lights with a diameter of up to 40 mm. (I strongly believe they are all the same size. :D

Important: DO NOT USE REAL CANDLES or you can have an indoor BBQ. ;D

Christmas Tree Topper with LED tea light

Star.3mf

This is my first “flexi” or articulated print in place model, and I always thought most articulated models are way to short. So I wanted to see how long I can make it. This one is almost exactly 1 m long.

Fits onto the build plate of the Bambu Lab P1S/P1P and X1C. For other printers you will most likely have to scale it down or UP? :D

Prints completely support free!

Have fun!

No commercial use. :)

XL Flexi Caterpillar

Caterpillarv4_final.stl

This is a 3D model for the CS:GO Skeleton knife. The knife is 230 mm (~9 in) long.

This is a 3D model for the CS:GO Skeleton knife. The knife is 230 mm (~9 in) long.
The download contains 3 different models, including the full body, and two different split version. One version is good for FDM printing (yellow / green as in the picture) and the other one is best for SLA,DLP or LCD printing (red /blue). I recommend using small pegs for best durability for the SLA version (Diameter: 3 mm or M3; Length ~ 15 mm)

Here is a full build video if interested: https://youtu.be/lnHOruZJqEE

Happy printing!

CS:GO Skeleton Knife

Skeleton Knife full.stl

A simple 3 part Kunai which is easy to print and assembly.

Naruto Kunai

Blade v2.stl

Bolt.stl

Grip v2.stl

This is a prop I made from the game Destiny: The Jade Rabbit.

This is the Jade Rabbit from Destiny fully printable on your i3 MK2 / MK3.

The model is split into several pieces for optimal printing / assembly and minimal support as usual. 

You'll need two ( or even 4  - for more weight and stability) 6mm rods with a length of 700 mm for better assembly. Please follow the assembly guide attached.

Have fun!

Destiny - Jade Rabbit 

Main Body 2 combined.stl

This is Minatos infamous "Hiraishin" Kunai from Naruto Shippuden.

Blade and Ring needs a little bit support to ensure smoother printing surface. All parts are rotated for optimal printing.

Print each file one time and have fun!

“Dattebayo”

Minato Kunai from Naruto Shippuden

Bladev3.stl

Be sure you have good build plate adhesion as he might jump away….

No seriously, the front legs have a slightly too steep angle, which can be hard to print if you do not have proper cooling and build plate adhesion. Other than that it's super easy to print!

Prints 100% support free.

Sorry for the file size and some not so sharp edges which are visible in the slicer. But it prints smooth and just fine. 

Cute Frog Sculpture "Froggo"

I transfered the Cryptopunk NFT to 3D printable pixels.
You have to print every pixel in the "desired" color. For easier printing they are named accordingly to a color. In addition you can see the "type" of block in the name as well as the number of blocks you have to print from this type and in this color.

E.g.: “Light grey x4_38”


This transfers to:

Color: Light grey
Type: 4x connections
Number: Print 38 pieces of this connector in the color light grey.
There's a PDF you can print out so you have a reference for assembly. It took me around 1,5h to assemble and over 100 hours to print all pixels.

I recommend printing a bunch more snap fits. Because you will have to break them if you made an error during assembly. ;)

 I also made one which you can see here: 
https://youtu.be/iS8E_96LbYc

NFT Pixelart - Cryptopunk#7523

Blue x4_112.3mf

These are some cute little dinos on a thin drawing template for kids. 

Dino Drawing Template for Kids

Addicted to 3DP since 2016. Making Prop / Cosplay stuff and hopefully usefull 3D printing every day.

Activity related to collaborating with others on models

Likes, comments, and activity from your community

A roundup of models that we think you'll like

For when we think someone might have posted your content as their own

New content from your premium memberships

Emails and messages from designers you follow

WF3D