Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:5382571.

Update 7 Mar 2023: Added another version V2 with a hole opening instead of an open V slot.

*****

Printed this https://www.thingiverse.com/thing:3606705 and wanted a drainer to go along.

*****
Want to buy me a coffee?https://www.buymeacoffee.com/zer0s

Clicking on my affiliate links below will give me a small kickback if you purchase something. (at no extra cost to you) 

AliExpress affiliate link:
https://s.click.aliexpress.com/e/_DeAZr9P

*****
Consolidated affiliate links of other 3D printing-related items:
https://wp.me/peMLu6-j

For Amazon affiliate links
https://wp.me/peMLu6-2C 

cutlery basket drainer

cutlery_basket_drainer_v2.3mf

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:5368393.

Update 2 May 2023: Add enlarged straw hole version (+0.2mm diameter). I have not tested printing this, will do so and update if issues are observed.

*****

I chanced upon this https://www.thingiverse.com/thing:5354341 and was impressed with the simple design. I have a few WD-40 and other spray cans with straws, tried it and it works!

I had some initial difficulty inserting the straw into the hole, it eventually went in.

And so I made some design changes to improve the straw insertion.

I had the hole for the straw elongated along a slant surface with a chamfer to guide the straw in easier.

I did it for the 360ml (65.5mm) and 250ml (52.5mm) can sizes. 

It seems better to me, hope others feel the same. 

*****

Want to buy me a coffee?
https://www.buymeacoffee.com/zer0s

Clicking on my affiliate links below will give me a small kickback if you purchase something. (at no extra cost to you) 

AliExpress affiliate link:
https://s.click.aliexpress.com/e/_DeAZr9P

*****
Consolidated affiliate links of other 3D printing-related items:
https://wp.me/peMLu6-j

For Amazon affiliate links
https://wp.me/peMLu6-2C 

Spray can straw holder

spray_can_straw_250_larger_hole.3mf

spray_can_straw_360.stl

spray_can_straw_360_larger_hole.3mf

Update 5 Jun 23: Added a new base foot with pin, so that there is no need to print the pin separately. However, fitment might be an issue for some printers, do a test print before mass printing.

*****

I love this simple modular design by B-Lab https://www.printables.com/model/483714-spools-desk-rack-modular

All parts can be used together interchangeably with the original design. 

The main interest should be the base foot found in the Remixed Parts folder which makes the structure more rigid and stable.

I am currently still printing more to expand, I want to see how tall I can stack it with one segment only with feet on four corners.

Other than the feet, I did some significant redesign on the support bar, the overkill version is stronger but prints with significantly more material. (assuming you use 10% infill like me, you will have to see the print preview to notice the difference in filament use).  I might start to print in the overkill version as I am seeing some sag in the normal support bar, I will update again.

For the rest of the parts, I added chamfers to my liking. 

Crosslink and spacer was my first attempt to make it less wobbly at the beginning, only to see not much improvement in stability. That's when I realized that the base needs to be wider for stability. Basically, it is adding crossbars to the top before stacking the next level. You are welcome to try it out, I might use this later as I build it taller/wider. 

Notes: 
If the triangle pins are too tight/loose, the easiest and cheapest modification is to shrink or enlarge the triangle pins in your slicer and reprint those. (2% onwards)

I have been adding for a while now, up to 4th stack the columns start to sway with some push/pull action sideways, though will return to the original position. Material is not bending, my guess is probably due to the joints not being rigid enough. It is fine for me, but I'll look into improving the rigidity further. 

I stopped stacking higher for now as the filament used per spool storage space is not very efficient. I can increase storage space by just adding one column instead of two if I extend it sideways.

*****

Want to buy me a coffee?
https://www.buymeacoffee.com/zer0s

Clicking on my affiliate links below will give me a small kickback if you purchase something. (at no extra cost to you) 

AliExpress affiliate link:
https://s.click.aliexpress.com/e/_DeAZr9P

*****
Consolidated affiliate links of other 3D printing-related items:
https://wp.me/peMLu6-j

For Amazon affiliate links
https://wp.me/peMLu6-2C 

Modular Spool Rack -Remixed! with feet for better stability

spacer.3mf

crosslink.3mf

triangle pin 23.3mf

end cap.3mf

Support overkill.3mf

triangle pin 19.3mf

top cap.3mf

base foot.3mf

triangle pin 13.3mf

Frame.3mf

Support.3mf

I have a few thick laptops to organize. 

I did a single laptop stand design a few days ago and expanded on that. 

Some overhang on the middle 2 ribs, will probably need supports to prevent sagging.  

*****
Want to buy me a coffee?
https://www.buymeacoffee.com/zer0s

Clicking on my affiliate links below will give me a small kickback if you purchase something. (at no extra cost to you)

AliExpress affiliate link:
https://s.click.aliexpress.com/e/_DeAZr9P
*****
Consolidated affiliate links of other 3D printing-related items:
https://wp.me/peMLu6-j

For Amazon affiliate links
https://wp.me/peMLu6-2C

Vertical laptop stand (3 laptops)

So I have a few thick laptops to organize. 

I did a single laptop stand design a few days ago and expanded on that. 

Some overhang on the middle 2 ribs, will probably need supports to prevent sagging.  

*****
Want to buy me a coffee?
https://www.buymeacoffee.com/zer0s

Clicking on my affiliate links below will give me a small kickback if you purchase something. (at no extra cost to you)

AliExpress affiliate link:
https://s.click.aliexpress.com/e/_DeAZr9P
*****
Consolidated affiliate links of other 3D printing-related items:
https://wp.me/peMLu6-j

For Amazon affiliate links
https://wp.me/peMLu6-2C

Activity related to collaborating with others on models

Likes, comments, and activity from your community

A roundup of models that we think you'll like

For when we think someone might have posted your content as their own

New content from your premium memberships

Emails and messages from designers you follow

Zer0s