After many, many, MANY different variations and tests with my previous interlocking hexes, I've seen the light and understood that printing the lids separately was a dumb idea.

So, new stacker hex! Prints like a charm! Even on a resin printer, if you print it with the lids straight on the table, you won't need supports for the small nubs, as they don't need to be precisely angular to work. By the 4th layer, everything will be properly glued together and it will fit into any needed hole.

=DIMENSIONS=
Face to Face:  30.39mm (outer); 27.03mm (inner, lid)
Edge to Edge: 35.10mm (outer), 31.22mm (inner, lid)
Height: 10.8mm + 1.7mm (lid) = 12.5mm total

The h4 variants are the equivalent of 4 hexes stacked on top of one another, which is enough to be taller than a typical RPG miniature, so one way to look at the hexes is that each layer could represent 50cm of real height, thus the tall pieces would be approximately 2 meters tall.

=LICENSE=
You ARE allowed to: print and remix this file however you see fit, share your edited files, sell the finished prints, create molds of this model
You are NOT allowed to: sell or charge money for access to the digital files, whether the original or modified versions

=THOUGHTS=
I suppose making a bunch of clipper nubs instead of having them built in into the pieces could work better? Converting these to that would be just a matter of cutting away the existing nubs, so no loss of compatibility

Hexes for stacking

hexinn.stl

A very orky looking leg for killa kans and maybe deff dreads too.

Currently scaled to work with Thorlek's Killa Kans, which are probably too big? 
Anyway, you can get them here: https://www.thingiverse.com/thing:4612598

Leg for Killa Kan

Similar to my previous command dice model. This is for use with the Firefight skirmish game from Mantic ([you can get their free starter rules here](https://www.manticgames.com/games/digital/firefight-digital-rules-free-sample/))

I decided to use chevrons instead of swords due to personal preference, I think it's more fitting. All the positions for values of 0, 1, 2 and 3 are the same.

This model is released under a BSD license. Do what you want, sell the prints, have fun.

Alternative Firefight Command Dice

cd-chevron-black.stl

These are the 3 different colored command dice used for Mantic's Firefight skirmish game. These are all scaled at 15mm, which should be the default size of most RPG dice.

I did the whole thing on Blender in around 20 minutes, so no copyright infringed anywhere.

While I'm not connected to Mantic in any way, I highly recommend you check out their Firefight game ([this is their free starter rules](https://www.manticgames.com/games/digital/firefight-digital-rules-free-sample/)), especially if you're looking for something more streamlined, compared to 40k. 

This model is released under a BSD license: you're free to do as you will with this model. You can sell prints.

Firefight Command Dice

ff-black-command.stl

Same model as the [4cm interlocking hex](https://social.thangs.com/m/578468), scaled down to 35mm face-to-face and a bit over 4cm between opposing vertices.

The lock is the same, you can slide this piece on the larger one. The 2 teeth version is there because, otherwise, you won't be able to make a stack and put a lid on something 1 level lower. Given how well they fit and stay, leaving it with only one tooth would suffice.

Same license, you can use this, remix this, upload modified versions, print this, sell the prints. You CANNOT sell these 3D models in any form, nor claim authorship of the designs.


Interlocking 35mm Hex tile

HX-35-FINAL-1cmalt.stl

Uses the same locking tooth as my hexes. Figured some people prefer squares, so here they are.

Same license, you can use this, remix this, upload modified versions, print this, sell the prints, pretty much anything. You CANNOT sell these 3D models in any form, nor claim authorship of the designs.


Interlocking square tiles - 33mm

QUAD-33-FINAL-1cmalt.stl

DIMENSION: 4cm between faces (edges), 4,36cm across opposing vertices

Comes with:
- Frame with teeth on all sides (hex-4cm-frame) 
- Frame with teeth on 3 sides (hex-4cm-3teeth), useful fo
- A top lid (hex-4cm-lidcover), feel free to create variations of this one for specific terrains
- Solid tile (hex-4cm-filled)

A simple interlock similar to those of puzzle pieces. You should be able to snugly snap them into one another coming from either the top or the bottom.

I have test-printed them with resin on a 2k resolution machine (kingroon KP6) and, after post-processing, most fits were still good, though a few were too tight. Your mileage may vary

You are free to do whatever you want with these models, **EXCEPT**
- claim either or both as your own design;
- sell the 3D models in any way other than as finished prints;

4cm Interlocking Hex Tile - Frame and Full

hex-4cm-frame.stl

hex-4cm-3teeth.stl

hex-4cm-lidcover.stl

Original Zerber - https://www.thingiverse.com/thing:1789712

This is a side panel + track for the Zerber chassi. Mirror it for the other side. Have fun

V2 Track for Zerber Chassi

Just a random dude you wouldn't notice walking down the street

Activity related to collaborating with others on models

Likes, comments, and activity from your community

A roundup of models that we think you'll like

For when we think someone might have posted your content as their own

New content from your premium memberships

Emails and messages from designers you follow

MisterMano