Needed are those prints, 4 M3 bolts and 4 screws

ATX PSU breakout Desk mounting plate

plate.stl

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:5223106.

A Ferris wheel to print and assemble with a bit of dedication and super glue in the right places. Design isn't perfect since it was just a gearbox test and show model for fun. It can be driven by a handle with a angled gear set inside. Add a bit of lubrication in to all parts that are sliding amongst other parts if needed.

Supports needed there where you deem them necessary. 


Design by Regina Omta https://www.reginaomta.com/

Luckily she was kind enough to let me share this for everyone!

Ferris wheel

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4260648.

Coldshoe splitter to mount up to four ascesoires on top of your camera like my 18650cell mount or my lightning trigger.

You might need a dap of superglue to glue in the foot. Top tip, first screw on the nut ;)

Camera Coldshoe Splitter

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4255941.

I made this to fit a 18650cell on top of my camera to power arduino driven triggers. I use a hotshoe splitter to mount both my arduino projects and this battery.

Assembly is easy! Just screw it together like you see in assembly.jpeg onlyuse a little superglue to permanently fix the foot into the middle piece. (Do not forget to screw on the nut before using superglue otherwise you have to reprint some parts ;) )

I took of the plastic protection on one sice of two jumer wires and put those ends trhough the endcap holes. the contact is made by sandwiching the battery cell between the endcaps with the wires touching the battery terminals.

Print everything once except for the endcap which you need to print twice to make one of those holders.

18650 hotshoemount container

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4802476.

Made this to replace the broken knob in my Fiat Panda. you have to remove the reverse gear blocker for this to work. Getting used to aiming for 5th instead of hitting the reverse blocker was about 2 days for me.

Big comfy shifter knob. 10mm rod hole compatible

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4663211.

Made a slightly deeper sit point for the nut so it actually uses the lock ring of the locknut.

Longboard wheelguard for kegel 80mm wheels

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4287837.

A first version of a discreflector arca mount. to use a normal tripod as stand for a disc reflector/softscreen.

Disc reflector arca tripod mount

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4335773.

Quick pop in replacement part for the Holden Crewman glovebox endstop. The rubber original ones were just destroyed.

Holden Crewman glovebox endstop.

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:3209470.

I had 30 minutes spare time, I know the scale is not accurate to the original benchy. I maybe revisit the design and make it a little more benchy I think it now is just a bit to much f1

This thing was made with Tinkercad. Edit it online https://www.tinkercad.com/things/9vdrh32IYfr

#F1 Benchy

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:3730714.

"To attach the two printed parts i've designed it to use 2 m3x10mm hex cap screws. The holes should be just small enough that the screws can self tap. So please don't over tighten."
-The original designer-


The ultimaker and Mankati Fullscale XT are almost the same so with a little adjustment on the axle spacing it is useable on the Mankati Fullscale XT.

1. Print this, all models are to be printed without support
2. Disassemble your printhead
3. Remove red block
4. Put on mount
5. Add your E3D v6 or vulcano head.
6. Add clamp
7. Add fanduct or fanduct BLtouch if you installed a BLtouch

Mankati Full Scale XT - E3Dv6 / Vulcano mount

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4528987.

Made this threadless nut with a 4.8mm hole and a 35mm base to hold up a blastic cover above my feet in my Holden Crewman

Threadless nut, 4.8mm hole, 35mm base

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4320279.

This is a bike pump to inflatable unicorn adapter. Might work on other inflatable objects to. The pump I have fits car tire valves as well.


Bike pump to Inflatable adapter

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4333723.

Little cover plate replacement for the rear bumper spare wheel tool hole in my Holden Crewman. Made one with a little camera cable cutout too since I have a rearview cam installed.


Holden Crewman bumper wheel winch hole cover

Activity related to collaborating with others on models

Likes, comments, and activity from your community

A roundup of models that we think you'll like

For when we think someone might have posted your content as their own

New content from your premium memberships

wesley.eenjes