The design on this cup was generated from an AI prompt in Microsoft's image generator.  I manipulated the image file to create a .stl file. I was hesitant about printing the model because the edges looked too rough and portions of the design seemed too extended, but I decided to take a chance anyway. The cup turned out just as I wanted without additional sculpting. 

I printed at 70% scale on MK3s+ with Fillamentum Extrafill PLA Peppered Mustard. 

Zentangle Lotus Cup

Lotus round base.stl

Activated carbon container. This was printed upside down without supports using FormFutura High Gloss PLA ColorMorph Gold & Silver.

Air Filter 

Air filter v 3db2.3mf

Stackable storage bins. 

The models in the photograph were scaled 77%.  

Rhombin

Stackable bin r3.stl

CSU Modular Storage Drawers with lids can function as a separate unit or on a shelf. The assembly is entirely 3d printable and has space for holding socks, underwear, hand towels, or other items. The tall drawer measures 7 1/4" Length, 11 1/4" Width, 8 7/8" Depth. Measurements for the shorter drawer are the same except for Depth, which is 4 1/2".

One set of drawers (tall, short) has square front corners, the other set has rounded front corners. 

Three different handles are included.

CSU Modular Storage Drawers

CSU drawer pull short final small.stl

3D printable parts combine with solid wood or plywood to make tables or etageres that give you many space organization options.

The brackets were assessed by an Independent Contractor Engineer.

Tubular parts are scalable.

Use 1/2" wood products to make a sturdy end table.

Bracket pairs extend 11 7/8". Dowels are required for the vertical columns; 5/8" diameter.

Engineer Umar Khalil assessed the bracket file.


Shelving unit 

Model1.STL

The finished shelf measures 12 1/4" W x 11 1/4" L x 8" D (back). It attaches to a wall with 4 - 3M Command™ Strips; each strip 6 to 12 lb capacity, depending on the infill percentage. A sturdy shelf is achievable with 20% infill.

Modular Wall Shelf

CSU shelf r2 left back1.stl

There are two sets of shelves. One set has the cross bars included in the design and the other set has separate cross bars. In each set, one can be attached with Command Strips and the other attaches with wall screws.

Dimensions: x - 243.87mm, y - 60.5 mm, z - 46.59 mm

I printed my shelf with Overture White PLA on a CR10 mini, modified with dual Z-axis, direct drive extruder, 0.6 steel nozzle, and borosilicate glass plate. The shelf was sliced in Cura 4.13.1, 0.30 layer height, temperature 210°, bed temperature 57°.

Glue is required to inset the cross bar.

Bath shelf i3 

Bath shelf i3 sep bar w holes.stl

Cabel Vase

Cabel vase.stl

Yuko is a contemporary vase with 2 stand options. The height of the vase itself is 7 3/4 inches (197.81 mm). Total model height is 10 3/8 inches (265 mm).

Yuko Vase

Orbic vase.stl

Art deco and contemporary styles come together in this unique finial. Its style-spanning design will enhance any window treatment.

Dimensions: 5.75"" (146 mm) x 5.9" (151 mm) x 6.4" (163 mm). Fits 1" (25.4 mm) round rods.

Aura Ascent

Curtain finial 3b.stl

Greano is a 3D printable table bracket set that lets you design and build your own unique end table or nightstand. Its contemporary lines and playful curves add a touch of whimsy to any decor.

Instructions for making a table with the brackets are included as a PDF file. PLA/PHA, PLA+, or any strong and flexible filament is recommended for best results and longevity.

The 3d printed shelf shown in the photographs is not part of the set as shelf dimensions are determined by desired table size. 

I included a bottom cap in the downloadable models, even though I decided not add it to the printed table. 

Greano 

Greano bracket r2 3b.stl

You can make a different sole part by outlining your foot instead of using the model part here or resize this sole part in modeling software before printing. After printing, the model can be cut with scissors to fit your slipper or similar shaped shoe. 

I printed the models shown in the photograph with a 0.6 nozzle on a CR-10 mini printer. 

Top and bottom layers should be reduced to 1 in your slicer. With a 0.4 nozzle, you will have a more pliable print if you decrease the z-height of the model to 0.4.

Snug Hugger

Foot sole plain 06.stl

Wall shelf for home decor items. A hollow version of the file is included.

Dimensions: 236 mm Length x 140 mm Width x 79 mm Depth.

Wedge Shelf

wedge shelf r.stl

The bottom of the coaster is for collecting condensation that falls through the holes at the top.

I used a glue gun to put 3 strips of melted glue on the bottom for traction. 

Coaster - 2 Parts

Coaster r3.stl

Comb - Curly Hair

Storage and organization bin inspired by The Container Store's Like-it Bricks bins. 

Triangle Bin - Tall and small

Triangle bin tall.stl

Pentagon Bin - Tall and small

Pentagon bin tall.stl

This bowl was inspired by West Elm's Form Studies Ceramic Bowls.
Dimensions - 198 mm round, 116 mm height.
Two versions are included. One version is a distressed bowl. 

Konic Bowl Smaller

Konic bowl smaller.stl

This bowl was inspired by West Elm's Form Studies Ceramic Bowls. 
Dimensions - 185 mm round, 121 mm height. 

 Konic Bowl

Bin for the organization of small items. 
Dimensions: 7.1" (182 mm) square x 5.2" (140.3 mm) height

Grid Bin 

Shelf for hanging scarves and storing small items. Can be used with the bar section turned upright or downwards.

Reversible Ledge

A round pencil cup. This is part of the RS design collection.
Dimensions: Diameter 72.92 mm x Height 112.67

RS Pencil Cup

Two files are attached; one with a hole for a screw head and one for damage-free  hanging with 3M Command Strips. 

Wall Hook

Hook w back.stl

The year was 2013, and I was knee-deep in Blender, crafting revolving planets and hockey-playing spatulas. Little did I know, a Motorola-sponsored Maker Lab in my local library held the key to transforming my digital creations into physical marvels. The hum of the 3D printer became my soundtrack, each layer of plastic whispering tales of possibility. From the library's printer to the trusty RepRap Prusa i3 and the MK3s+, my tools grew along with my ambitions. My journey continues, fueled by a passion for creation and the endless potential of 3D printing.

Activity related to collaborating with others on models

Likes, comments, and activity from your community

A roundup of models that we think you'll like

For when we think someone might have posted your content as their own

New content from your premium memberships

Emails and messages from designers you follow

<div class="markdown"><p>The year was 2013, and I was knee-deep in Blender, crafting revolving planets and hockey-playing spatulas. Little did I know, a Motorola-sponsored Maker Lab in my local library held the key to transforming my digital creations into physical marvels. The hum of the 3D printer became my soundtrack, each layer of plastic whispering tales of possibility. From the library&#x27;s printer to the trusty RepRap Prusa i3 and the MK3s+, my tools grew along with my ambitions. My journey continues, fueled by a passion for creation and the endless potential of 3D printing.</p></div>

cSandra