#gridfinity 1x2 block that holds a bunch of male USB things. Has:
- A lot of (N) USB A slots
- (N/2) micro USB slots
- (N/2) USB C slots

gridfinity usb holder

gridfinity usb holder female a, micro, c 1x2

Magnet jig to help you glue magnets to #gridfinity baseplates.

I tried other baseplate jigs that didn't work well for me. This one is dead easy to use. 

Once you've glued magnets in the jig in the right orientation:
1. Put some glue in the magnet holes in a slot of your baseplate
2. Slip the jig into place UNDER that slot in the baseplate so the jig pins fit in the plate holes
3. Drop some magnets and they'll fly right into place facing the right way
4. Remove the jig

I've installed magnets in many baseplates this way—makes it a breeze!

gridfinity baseplate magnet jig

gridfinity baseplate magnet jig underside

Stackable bins based on:
- Yuan4114's https://www.thingiverse.com/thing:647425 
- which is a remix of Gushie's http://www.thingiverse.com/thing:447213, 
- which is a remix of 1986breeze's http://www.thingiverse.com/thing:234669, 
- which is a remix of martinhering's http://www.thingiverse.com/thing:177814

You may also be interested in my [stackable shelves](https://thangs.com/designer/benkrejci/3d-model/stackable%20shelf-817729), which is basically this without the front.

I started from scratch so I could make it parametric in Fusion 360. Also made some changes:
- The shelf for the next bin to sit on now goes all the way to the back on both sides
- Mid slot fits optional divider (included in various sizes)
- Chamfered bottom and top mating edges make nesting a dream
- The side channels go the same direction so they fit together when placed side-by-side
- Some other changes

I included various common sizes as well as the Fusion 360 file if you want to choose your own—the f3d file is fully parametric.

Uploaded by Thangs Sync

stackable bins - parametric

divider 100x75mm.stl

divider 100x100mm.stl

divider 140x70mm.stl

divider 140x105mm.stl

divider 180x90mm.stl

divider 180x135mm.stl

divider 220x110mm.stl

divider 220x165mm.stl

divider 220x220mm.stl

bin 30x60x30mm.stl

bin 50x100x50mm.stl

bin 60x60x30mm.stl

bin 60x60x45mm.stl

bin 60x60x60mm.stl

bin 70x140x70mm.stl

bin 90x180x90mm.stl

bin 100x100x50mm.stl

bin 100x100x75mm.stl

bin 100x100x100mm.stl

bin 110x220x110mm.stl

bin 140x140x70mm.stl

bin 140x140x105mm.stl

bin 140x140x140mm.stl

bin 180x180x90mm.stl

bin 180x180x135mm.stl

bin 180x180x180mm.stl

bin 220x220x110mm.stl

bin 220x220x165mm.stl

bin 220x220x220mm.stl

divider 60x30mm.stl

divider 60x45mm.stl

divider 60x60mm.stl

divider 100x50mm.stl

divider 140x140mm.stl

divider 180x180mm.stl

#gridifinity tweezer rack. Remixed from [Zack's rack](https://thangs.com/designer/ZackFreedman/3d-model/Gridfinity%2520Pick%2520%252B%2520Tweezer%2520Racks-60742) to be printable in one shot.

gridfinity twizzles rack single piece

gridfinity Twizzles Rack Upper-single piece.stl

#gridfinity spool holders. Thread your wire (or whatever) through the hole and just pull it out when you need it. I find this easier to print and use than spool holders with axles.

Included are 2x3 blocks for:
- Standard 20x55mm wire spools
- Wider 34x55mm which fits most thiccboy solder spools

[Parametric fusion 360 file](https://a360.co/3Qas8xu) Just specify the spool size and slots wide/deep and it will adjust automatically to fit the max number of spools.

gridfinity spool holders

gridfinity spool holder 2x3 20x55mm

1x1 gridfinity block for holding a bunch of 4mm hex bits. They're pretty tightly spaced so keep that in mind—it can be kind of hard to grab 'em.

Uploaded by Thangs Sync

gridfinity hex bits

gridfinity hex bits 1x1 22 bits.stl

#gridfinity 1x1 block that holds 5 standard razor blades.

gridfinity razor holder

1x4x1 #gridfinity block 3d printer tool caddy. I use this to hold:
- Chisel
- Glue stick
- 2x wire brushes
- Xacto knife
- 4 Allen keys
- Scissors (tip down)

gridfinity 3d printer tool caddy

gridfinity 3d printer tools

Stackable shelves for when you get annoyed by the front of your bins and realize you wanted shelves all along.

Very similar to [my parametric stackable bins](https://thangs.com/designer/benkrejci/3d-model/stackable%20bin-817741) but with no front.

I Included various common sizes as well as the Fusion 360 file if you want to choose your own—the f3d file is fully parametric.

Uploaded by Thangs Sync

stackable shelves - parametric

shelf 30x60x30mm.stl

shelf 140x140x70mm.stl

shelf 140x140x105mm.stl

shelf 140x140x140mm.stl

shelf 180x180x90mm.stl

shelf 180x180x135mm.stl

shelf 180x180x180mm.stl

shelf 220x220x110mm.stl

shelf 220x220x165mm.stl

shelf 220x220x220mm.stl

shelf 50x100x50mm.stl

shelf 60x60x45mm.stl

shelf 60x60x60mm.stl

shelf 70x140x70mm.stl

shelf 90x180x90mm.stl

shelf 100x100x50mm.stl

shelf 100x100x75mm.stl

shelf 100x100x100mm.stl

shelf 110x220x110mm.stl

shelf 60x60x30mm.stl

#gridfinity 1x1 block cylinder holder. Holds [Starbond brand CA glue](https://www.amazon.com/dp/B00C32MHJU) or anything 35mm in diameter with some wiggle room.

gridfinity ca glue holder

gridfinity ca glue holder.stl

#gridfinity 2x2 block to hold [this hakko soldering iron tip cleaner](https://www.amazon.com/gp/product/B00FZPGDLA). Printed with 0 clearance to sit super snug.

gridfinity hakko brass solder sponge holder

gridfinity brass solder sponge holder

Mount adapter to interface [raspberry pi camera articulating mount](https://www.thingiverse.com/thing:3114849) with 3030 aluminum extrusion using a couple of m3 bolts and t-nuts ([I also 3d printed the nuts](https://www.printables.com/model/38366)).

I use this to attach the articulating arm with camera to my Prusa Mini

[Fusion 360 model](https://a360.co/3RjRtXk)

articulating mount adapter

female 3030

Made to be an ice scoop. Prints in place without supports. Designed for the handle to stick up out of the ice bin so I don't have to stick my dirty fingies in there to get ice (which would defeat the whole purpose of having a scoop).

Scoop

ice scoop.stl

#gridfinity nippers/needle-nose-pliers holder with tips down!

While appreciate Zack's humor, I've found that I don't appreciate putting my fingies right in the pointies. This design alleviates that problem by assuming you can tell the difference between your nippers by their handles.

I spent an unreasonable amount of time getting all my tools to fit in one hole (that's what they said) but your mileage may vary.

gridfinity nippers tip-down!

2x3.stl

#gridfinity 1x3x1 block calipers caddy with some extra tools. I use this to hold:
- [No-name Amazon calipers](https://www.amazon.com/Electronic-Stainless-Measuring-Extra-Large-Conversion/dp/B073XJJRXB) (which are a different size from Zack's)
- 4 Hex drivers
- 8mm Xacto knife

gridfinity calipers and misc caddy

gridfinity caliper and misc

Holds the brush head upside-down so the yucky stuff drips in the tray.

Inspired by a different design I saw somewhere, but can no longer find.

In case it's not obvious: it's easiest to insert the brush head by placing it down into the hole rather than trying to snap it in from the front.

Prints upright without supports.

oral-b toothbrush head stand with drip tray

stand

Fits 10x2 mm rare earth magnets. CA glue 'em in and voila, now you have something to grab onto.

Uploaded by Thangs Sync

fridge magnets

gripped.stl

poly.stl

I like to hang things from my drop ceiling tracks. I use the ball hooks to hang sound dampening blankets with 1" grommets and I use the wire guides to... guide wires.

The edge clip is for edge tracks which are typically against a wall.

You'll definitely need supports for the 90deg wire guide. I printed it exactly upside-down relative to it's normal hanging position.

Uploaded by Thangs Sync

Drop ceiling panel clips

Drop panel clip wire guide 90deg.stl

Drop panel clip ball.stl

Drop panel clip wire guide.stl

Drop panel edge clip ball.stl

Drop panel wire hanger.stl

Drop panel clip ball right angle.stl

#gridfinity 2x2 block to hold 49mm flux jar. Printed with 0 clearance to sit super snug so that I can unscrew the lid with one hand and the jar stays put. [This is the flux I use with it](https://www.amazon.com/gp/product/B000G33PAI).

gridfinity flux holder

gridfinity flux holder 47mm

I use this to hang cables on the wall. Sized to fit in a Prusa Mini (180mm cube).

- 3mm diameter screw holes
- 20mm channels for hanging with 3M command strips
- 7mm space between tines
- 18mm tine width

cable comb (wall-mounted cable holder)

cable comb

See my [blog post about this](https://www.benkrejci.com/projects#RFID-Cat-Feeder)

Uploaded by Thangs Sync

RFID Cat Feeder

Base.stl

Bobbin.stl

Lid.stl

Platform.stl

Coil Arm Left.stl

Coil Arm Right.stl

Spur gear.stl

Parametric slide-together picture frames. To assemble (note that 3 out of 4 of the corners are trapezoidal mating tracks, while the fourth is rectangular):

- Slide 3 edges together (only use trapezoidal tracks; leave an edge with a rectangular track aside for now)
- Insert the piece to be framed into the inner slots
- Slide the remaining frame into place.
It may be necessary to glue the square track depending on the dimensions and orientation. 

I find the frame holds itself together just fine without glue.

I print the 4-edge groups diagonally at 45° so that I can accommodate the largest frame possible on my build plate.

[Parametric Fusion 360 file](https://a360.co/3BdRxCd)

picture frames

beveled 140x180mm

Used to attach [DWV9000 adapter](https://www.amazon.com/DEWALT-DWV9000-Universal-Connector/dp/B00B6K4VKS) (threaded side) to a 1-3/4" OD shop vac hose. I could after buying a few adapters that did not fit my Rigid shop vac, I printed this.

**NOTE:** The threads are left-handed for some reason, so remember to turn counter-clockwise to tighten.

Uploaded by Thangs Sync

dewalt dust extractor adapter

1-5∕8in thread to 1-3∕4in OD hose.stl

Drip dish in various sizes for sponges, brushes, etc. I put mine behind the sink so they drain into it.

I printed these in ABS and they tolerate the dishwasher fine. It is designed to be printed sitting on the back face. I printed the 240mm one on my Prusa mini (180mm^3 volume) by rotating it 45 deg on the plate and removing the skirt. I had to add some pretty wide feet in PrusaSlicer to keep the ABS from warping off the plate.

Uploaded by Thangs Sync

sink dishes

sink dish 180x138mm.stl

sink dish 200x138mm.stl

sink dish 220x138mm.stl

sink dish 240x138mm.stl

sink dish 180x100mm.stl

sink dish 200x100mm.stl

sink dish 220x100mm.stl

sink dish 240x100mm.stl

sink dish 172x138mm.stl

sink dish 236x138mm.stl

sink dish 230x138mm.stl

Designed to barely fit on my Prusa mini (180mm^3 build volume).

I use it to pour desiccant beads from a baking sheet back into the jar.

Uploaded by Thangs Sync

big-ass funnel

funnel.stl

I like my ZSA moonlander MK1 to tilt out and forwards (like my hands are resting on the top of a big bouncy ball) without tenting the thumb clusters.

Printed this in 2 interlocking pieces so that each can fit in the build volume of a Prusa Mini (180mm cube).

Has holes for M2.5 screws to mount keyboard and tabs on the underside that I stick rubber feet on.

ergonomic zsa moonlander tilt stand

Stand L

I put 2 of [these scrubber brushes](https://www.amazon.com/gp/product/B07FCH67ZQ) in one of these under my kitchen sink. Keeps the cabinet from getting nasty.

[Parametric Fusion 360 model](https://a360.co/3AOEXI2)

scrubber brush drip dish

brush drip dish 140x160mm

I made this desiccant box to fit behind the filament spools inside dryboxes made from [this storage 47 qt. tub](https://www.amazon.com/gp/product/B084DY21D6). It also fits inside the build volume of the Prusa Mini (180mm cube).

I have one of these sitting snugly behind the spools in all my dry boxes.

**Assembly:**
- Print 3 parts as oriented (no supports)
- Glue the top on the body
- Fill with desiccant beads
- Screw on the top

desiccant box round

body

cap.stl

top.stl

Some gridfinity holders for my meters and scopes. Fits the following cheap meters:

- [Proster LCR meter](https://www.amazon.com/gp/product/B071WNNYQT)
- [Bside multimeter](https://www.amazon.com/gp/product/B07P7V3YNT)

And my OWON USB oscilloscope. 

Uploaded by Thangs Sync

gridfinity meter holders

gridfinity proster bm4070 lcr meter holder.stl

gridfinity zt-x multimeter holder.stl

gridfinity owon oscilloscope holder.stl

Snaps into the pot lights that came in my ceiling. They have a 6.375" diameter opening at the base and 3 spring balls which slot into the ring on the baffle.

Uploaded by Thangs Sync

can light baffle

6.5in can light baffle.stl

Holds 2 standard Thunderbolt "certified" plugs together so they fit into a MacBook Pro. Makes it easier to plug 'em in if you do it a lot.

Uploaded by Thangs Sync

thunderbolt coupler

Thunderbolt coupler.stl

Designed for the Gigabyte M32U monitor which has a really useful KVM feature, but really annoying button placement which makes it impossible to use if you have another monitor to the right of it.

This is a print-in-place hinged arm that comes out under the bottom of the monitor so I can press the KVM switch from the front. I just taped the stationary part of the hinge to the back of the monitor and it works perfectly.

Uploaded by Thangs Sync

Gigabyte Monitor KVM button pusher

KVM pusher.stl

imperial nut

5-16 nut

I designed this sponge rack to fit exactly on the back of my kitchen sink, flush with the counter fillet so that it drips into the sink.

I printed it out of ABS and wash it in the dishwasher no prob.

[Parametric Fusion 360 file](https://a360.co/3BdCBE1)

sponge rack

sponge holder

Activity related to collaborating with others on models

Likes, comments, and activity from your community

A roundup of models that we think you'll like

For when we think someone might have posted your content as their own

New content from your premium memberships

Emails and messages from designers you follow