This is a replacement for the Helmet Flair small helmet horns. Lost one? Print a new one!

Uses 6mm magnets, easily attainable from the overlords. Glue in with hot glue or super glue.

I'd recommend printing with the base down, maybe 15-20% infill, and tree supports.

Stay horny!

Magnetic Helmet Horns

Onewheel Pint Mini Fenders

Pint Mini Fender LED Notch v1.stl

Some simple shorty fenders with nice curves

Onewheel XR Mini Fenders

XR Mini Fenders

Got Varials? Want bash guards to keep those steezes pristine? Here ya go!

These ones are designed to fit the straight or LOL steezes. I might design some for WTFs and FAFs if ppl want them. Lmk.

Onewheel XR Varials Center Steez Bash Guards

Center Steeze Bash Guards.stl

Rail/bumper guards for the Pint and Pint X!

These protectors are curved perfectly to match the shape of the Pint rails, so they can be printed in PLA (the flat-back designs need to be printed in TPU to bend to the curved rails).

Slice parts with the flat outside face against the bed. For a full set, print 2x center rail guards, and 1x of each corner guard. Use double-sided adhesive tape to mount.

Onewheel Pint Rail Guards

Left Rear Rail Guard.stl

Got Life Savers? Want a nice clean fender delete that works with your Life Savers? Here ya go!

They're 6.75mm tall to match the height of the footpads for an even surface. There are two versions, one for the mag handle and one for no handle. And there are a split and a single-piece version of each depending on how large your print bed is. Glue the split halves together with CA glue and they'll be solid enough to mount without adhesive tape.

Onewheel XR Fender Delete - Life Saver Compatible

XR_Fender_Delete_No_Handle.stl

The stock fender has a small gap between the feet and the rails. These spacers fill that 1.5mm gap to set the fender height correctly without pinching the grip tape. They also add some fun flair to the top of your rails, and give the board a nice clean look. Notches are designed to fit Life Savers.

Onewheel XR Fender Spacers - Life Savers Compatible

XR_Fender_Spacer_No_Handle.stl

THE MOMENT YOU'VE ALL BEEN WAITING FOR!

Finally you can have your lid and stack it too! Stackable lids are here to stack your Gridfinity bins even higher!

These stackable lids allow you to stack smaller modules on top of larger bins. Want to store your 4x2 bins on the bottom layer and then stack your 2x1 and 1x1 blocks on top? NOW YOU CAN!

Gridfinity Stackable Lids

GF_stackable_lid_4x2.stl

GF_stackable_lid_4x3.stl

**Parametric templates for Gridfinity modules**

Models:

- Flat top box: this model is super useful for creating modules with holes or extrusions for holding whatever it is you want to hold. 


These models are fully parametric, so you can adjust the height/width/depth. 

The depth and width are set in units of 1 grid block. (e.g. 2 will give you 2 blocks wide)

Height is set as divisions of 6 (the standard "tall" blocks are actually 6 units high), so the parameter is set as X/6, where X is the height units. Setting 3/6 will give you a half-height block (or 3 units tall).

Design credit goes to Zach Freedman, the allmighty inventor of Gridfinity 🙇

Gridfinity Templates

GF_1x1x4_Template_3MF.3mf

GF_1x1x4_Template_FBX.fbx

GF_1x1x4_Template_OBJ.obj

GF_1x1x4_Template_STEP.step

GF_1x1x4_Template_STL.stl

GF_1x1x4_Template_USDZ.usdz

**Gridfinity label cartridge holders for Epson LK and PX labels**

The PX labels work in all of the LW-PX### printer models. The LK labels work in the LW-### models. However, with slight modification to the printer and label cartridge, the LK tape can be used in LW-PX### models as well.

These modules are fully Gridfinity compliant:
6 units tall
Stackable (with no cartridges inserted)
Magnet and M3 screw holes

_2022/07/19: added new extrusion to front of cartridge slots to accommodate the ridge around the label output slot_


Gridfinity Epson Label Cartridge Holder

GF_2x2x6_Epson_Label_Holder.3mf

GF_3x2x6_Epson_Label_Holder.3mf

GF_2x2x6_Epson_Label_Holder.stl

GF_3x2x6_Epson_Label_Holder.stl

Hark ye liquid nicotine enthusiasts! Have your numerous bottles of tasty inhalation fluids been scattered across your home with no hope of organization in sight? Fret no longer! For I have graced you with vape juice organization modules for Gridfinity!

There's also an organizer for your extra pods if you use a Smok Novo. It should work for pods for the Novo 1, Novo 2, Novo 3, Novo 4, and Novo X. Haven't tested yet, so let me know how it goes for you.

Gridfinity Vape Accessories Storage

GF_4x1x6_Vape_Juice_Holder

Activity related to collaborating with others on models

Likes, comments, and activity from your community

A roundup of models that we think you'll like

For when we think someone might have posted your content as their own

New content from your premium memberships

Emails and messages from designers you follow

Miss Adventure