Straighten out your workshop with Gridfinity modular storage - deploy these plates anywhere you need some order!

Gridfinity is the ultimate organizer for your whole workshop! Learn more at 
Find more Gridfinity accessories at https://bit.ly/3E2NxnZ

Parametric source files: 
- Frame: https://a360.co/3ccHbsg
- Weighted Plate: https://a360.co/3uCJ2gR

The foundation of every Gridfinity setup is a baseplate, and these let you drop storage where you need it most.

**Frame**: The absolutely minimal no-frills baseplate. No room for screws or magnets, but saves filament and headroom. If your storage unit is on a steel surface, you can still put magnets in the storage blocks to keep them from sliding.

**Weighted**: Heavy, sturdy baseplate perfect for desktops, shelves, and other places where knocking stuff over is a big problem. 

Secure blocks permanently with [M3 screws,](https://amzn.to/37IaXTg) or temporarily with [6x2mm magnets](https://amzn.to/37Ihopq). Add [rubber feet](https://amzn.to/3LZv4v5) to keep the whole shebang from sliding, and [metal tire weights ](https://amzn.to/3uAzH9f)to drop the center of gravity and prevent wipeouts. You don't need to install every magnet, foot, and weight! Just use enough for your needs.

A Prusa i3 Mk3 can print up to a 5x5 grid. No matter what you use, make sure your bed adhesion and release is dialed in - these love to curl, and their high surface area can make them challenging to remove.

**Gridfinity Tips!**
- No brims or support required! 
- Use any filament with an 0.6mm or smaller nozzle. 
- Wider plates can curl, so maximize your bed adhesion if you're going big!
- All storage blocks are compatible with all baseplates!
- Most storage blocks are stackable!
- You can add 6x2mm magnets to the corners! They won't magnetize the contents.
- You can also use M3 screws in the corners.

Gridfinity Baseplates

Weighted Baseplate 3x2.stl

Frame 1x4.stl

Frame 1x5.stl

Frame 1x6.stl

Frame 1x7.stl

Frame 2x2.stl

Frame 2x3.stl

Frame 1x2.stl

Frame 1x3.stl

Frame 2x7.stl

Frame 3x3.stl

Frame 3x4.stl

Frame 3x5.stl

Frame 3x6.stl

Frame 3x7.stl

Frame 4x4.stl

Frame 4x5.stl

Frame 4x6.stl

Frame 4x7.stl

Frame 5x5.stl

Frame 5x6.stl

Frame 5x7.stl

Frame 6x6.stl

Frame 6x7.stl

Frame 2x5.stl

Frame 2x6.stl

Weighted Baseplate 1x3.stl

Weighted Baseplate 1x4.stl

Weighted Baseplate 1x5.stl

Weighted Baseplate 1x6.stl

Weighted Baseplate 1x7.stl

Weighted Baseplate 2x2.stl

Weighted Baseplate 1x1 (super cute).stl

Weighted Baseplate 1x2.stl

Weighted Baseplate 2x4.stl

Weighted Baseplate 2x5.stl

Weighted Baseplate 3x6.stl

Weighted Baseplate 3x7.stl

Weighted Baseplate 4x4.stl

Weighted Baseplate 4x5.stl

Weighted Baseplate 4x6.stl

Weighted Baseplate 4x7.stl

Weighted Baseplate 5x5.stl

Weighted Baseplate 5x6.stl

Weighted Baseplate 5x7.stl

Weighted Baseplate 6x6.stl

Weighted Baseplate 6x7.stl

Weighted Baseplate 7x7.stl

Weighted Baseplate 2x7.stl

Weighted Baseplate 3x3.stl

Weighted Baseplate 3x4.stl

Weighted Baseplate 3x5.stl

Versatile open-top storage blocks for the Gridfinity modular workshop storage system - multiple sizes for infinite options!

Gridfinity is the ultimate organizer for your whole workshop! Learn more at  
Find more Gridfinity accessories at https://bit.ly/3E2NxnZ

Parametric source file: https://a360.co/3vbu9B5

These are perfect for storing small parts and long, thin objects like needle files, and you can stack them as high as you want! The inner surface has a generous scoop to make retrieving parts easy, and the tab fits 12mm label-maker tape.

I've provided a selection of different sizes and divider counts, to give you OPTIONS! Note that none of the compartment sizes overlap - there isn't a two-compartment 4x1 bin because you can just use two one-compartment 2x1 bins.

Dimensions in file names are Width x Depth x Height. Width and Depth units are 42mm grid slots, Height is in 7mm units. A Prusa i3 Mk3S can fit a five-unit-wide bin on its plate.

Note that two-unit-high bins don't have labels - they would cut too far into the usable storage area.

Brims and support are not required, and these can be printed in any filament with an 0.6mm or smaller nozzle. Wider bins can curl, so maximize your bed adhesion if you're going big!

**Gridfinity Tips!**
- All storage blocks are compatible with all baseplates!
- Most storage blocks are stackable!
- You can add 6x2mm magnets to the corners! They won't magnetize the contents.
- You can also use M3 screws in the corners. 

Gridfinity Divider Bins

Divider Box 2x1x6 5-Compartment.stl

This is a collapsing Katana sword designed to be printed as one part. Its only 182mm high when printed but expands to over 825mm in total length! The sword is designed to be printed with a ,4mm nozzle, the blade will be two shells thick.

I have updated this version to have a single edged curved blade. You can find it [here](https://social.thangs.com/m/192043).


There is a [Kanata test print](https://thangs.com/3dprintingworld/Katana-Test-Print-22695). If this works, you shouldn't have a issue. If it fuses together, I would suggest adjusting your cost and wipe settings.

Detailed printing instructions can be found on my [website]( https://www.dddprintingworld.com/pages/printing-collapsible-lightsabers-and-swords
)
For more info on how to print this, follow the links to my channel. 
https://youtu.be/YQV4PYJPhx0
https://youtu.be/xN0H9npkkP4

Help to support me by using the affiliate link for the gold filament used: https://amzn.to/2EjmdnF

**Collapsing Swords**
[Katana with Single Edge Curved Blade](https://social.thangs.com/m/48843)
[Katana with Removable Blade](https://social.thangs.com/m/46779)
[Master Sword]( https://thangs.com/3dprintingworld/Collapsing-Master-Sword-with-Replaceable-Blade-35659)
[Jian]( https://thangs.com/3dprintingworld/Collapsing-Jian-24803)
[Pirate Sword]( https://thangs.com/3dprintingworld/Collapsing-Pirate-Sword-24232)
[Board Sword]( https://thangs.com/3dprintingworld/Collapsing-Broadsword-24236)
[Dagger]( https://thangs.com/3dprintingworld/Collapsing-Dagger-24805)
___
**Support and Licensing**
If you would like to help support more free models please consider joining my Thangs [Membership](https://than.gs/u/35786?plans=true) 
To get permission to sell physical copies of my models, consider joining my [Patreon](https://www.patreon.com/3dprintingworld)


Collapsing Katana

This is a collapsing Katana sword designed to be printed as one part. Its only 182mm high when printed but expands to over 825mm in total length! The sword is designed to be printed with a ,4mm nozzle, the blade will be two shells thick.

There is a file named "test print". If this works, you shouldn't have a issue. If it fuses together, I would suggest adjusting your cost and wipe settings.

For more info on how to print this, follow the links to my channel. 
https://youtu.be/YQV4PYJPhx0
https://youtu.be/xN0H9npkkP4

Help to support me by using the affiliate link for the gold filament used: https://amzn.to/2EjmdnF

COLLAPSING-KATANA.stl

**Drill Sword**
_Print-in-Place Version_

This version of the Drill Sword prints complete all as one piece. 

The [Replaceable Blade Version](https://than.gs/m/909996) is available to my Thangs members. 

**Printing**
Supports are not required, for best results use a .4mm nozzle. Find detailed instructions on [how to print collapsing swords](https://www.dddprintingworld.com/pages/printing-collapsible-lightsabers-and-swords) on my website. If this is your first time printing, I would suggest you try the [test print]( https://social.thangs.com/m/23601) first. 

Printed on the [Muldex](https://github.com/3dprintingworld/MULDEX) rep-rap IDEX printer 
___
**Support and Licensing**
If you would like to help support more free models please consider joining my Thangs [Membership.](https://than.gs/u/35786?plans=true) Get permission to sell physical copies of my models by joining my [Patreon](https://www.patreon.com/3dprintingworld)



Collapsing Drill Sword Print-in-Place

**Drill Sword**
_Print-in-Place Version_

This version of the Drill Sword prints complete all as one piece. 

**Printing**
Supports are not required, for best results use a .4mm nozzle. Find detailed instructions on [how to print collapsing swords](https://www.dddprintingworld.com/pages/printing-collapsible-lightsabers-and-swords) on my website. If this is your first time printing, I would suggest you try the [test print]( https://social.thangs.com/m/23601) first. 

Printed on the [Muldex](https://github.com/3dprintingworld/MULDEX) rep-rap IDEX printer 
___
**Support and Licensing**
If you would like to help support more free models, or get permission to sell physical copies of my models, consider joining my [Patreon](https://www.patreon.com/3dprintingworld)



Safely grab the right tool with the Gridfinity modular workshop storage system!

Gridfinity is the ultimate organizer for your whole workshop! Learn more at https://www.youtube.com/watch?v=ra_9zU-mnl8
Find more Gridfinity accessories at https://bit.ly/3E2NxnZ

Parametric source files: 
- Nipper Holder: https://a360.co/37jchw3
- Stripper Holder: https://a360.co/3Erq2oV

These racks pack tons of hand tools into a small area, positioned so you can safely see and grab the business ends. These work great for nippers, flush cutters, wire strippers, pliers, scissors, crimpers, nibblers, cutters, and punch-down tools.

*These storage blocks are extra-big and tend to curl! Use a brim and ensure good bed adhesion.* 

**Nipper Holder**: Holds six tools about 80mm from handle to handle. If the tool is spring-loaded, the undercut will keep it from falling out. This can be mounted sideways to store five tools.

**Stripper Holder**: Holds two wire strippers or other long, slim hand tools up to 18mm thicc. I've prepared two sizes - 200mm is your usual multi-hole wire stripper, and 160mm fits many crimpers and termination tools. Both should fit on most printers.

**Gridfinity Tips!**
- Use any filament with an 0.6mm or smaller nozzle. 
- All storage blocks are compatible with all baseplates!
- Most storage blocks are stackable!
- You can add 6x2mm magnets to the corners! They won't magnetize the contents.
- You can also use M3 screws in the corners.

Gridfinity Nippers + Strippers + Pliers Racks

Nipper Holder x6.stl

Pointy boi storage for the Gridfinity modular workshop storage system - saves space and delicate fingies!

Gridfinity is the ultimate organizer for your whole workshop! Learn more at 
Find more Gridfinity accessories at https://bit.ly/3E2NxnZ

Parametric source files: 
- Pick Rack: https://a360.co/3JCOrIS
- Chonk Rack: https://a360.co/3xgYhO9
- Tweezer Rack: https://a360.co/3uxC0dd

These racks store long, pointy objects at an angle... but angle the business ends away from pokey fingers.

These are all two-part models. Print an Upper and a Lower and glue 'em together.

- The Pick Rack is perfect for slender tools like picks and files.
- The Chonk Rack is for thiccer tools (hey-o) like scrapers, forceps, and spring tweezers.
-  The Twizzles Rack holds tweezers. I call them twizzles because I think it's funny.

The Twizzles Rack Upper is the only piece that needs support.

**Gridfinity Tips!**
- No brims or support required! 
- Use any filament with an 0.6mm or smaller nozzle. 
- Wider bins can curl, so maximize your bed adhesion if you're going big!
- All storage blocks are compatible with all baseplates!
- Most storage blocks are stackable!
- You can add 6x2mm magnets to the corners! They won't magnetize the contents.
- You can also use M3 screws in the corners.

Gridfinity Pick + Tweezer Racks

Illustration! Don't print!!

A 3D printable maze puzzle box. This make for a great gift, instead of just giving out cash - make them earn it!

3D_Maze_Puzzle_Box

**Collapsing Master Sword with Removable Blade**

Unlike the Print-N-Place version, the pommel on the hilt of this Master Sword is threaded which allows the blade to be printed separately and inserted. The assembled hilt is 250mm long but the blade extends to a length of 870mm long in total!

**Printing**
The hilt and pommel do not require supports. The blades can be printed concentrically as an assembly or individually in vase mode. If you plan to print concentrically, a single stl contains all the blades. If printing in vase mode, there is a stl for each blade.  Note the vase mode stl’s are supposed to be solid so the slicer knows not to make an internal perimeter. 

**Vase Mode**
I prefer printing the blades in vase mode as the result is a much cleaner and easier print that can easily be scaled. If you print sequentially, it’s faster too.  If printing at 100% scale,  set the line width to .85mm. If you plan to print it smaller, scale the line width down by the same about.  If printing in vase mode you can scale down to a minimum of 55% with a .4mm nozzle.  For vase mode turn top and bottom layers on for the first blade, but turn it off for segments 2-5. You will notice that the vase mode files are solid, this is so your slicer knows not to try to build a inner perimeter. 

**Concentric**
When printing the blades concentrically use a .4mm nozzle and set the line width to .42 so the blades are two shell thick. If you would like to scale it down try printing the vase mode version instead. Before printing the blade assembly make sure perform the test print found [here](https://thangs.com/3dprintingworld/MASTER-SWORD-TEST-PRINT-35236)  This print is sensitive on the layer seam and might need to be tuned so the blades don’t fuse. 

**Test Print**
The test print is a total of 24mm high so I change retraction settings every 8mm.  Then I compare the changes until I achieve the best result. Each printer is going to be different but in my case I used a negative “extra restart” distance to reduce the size of the layer seam. 

Detailed printing instructions can be found on my [website]( https://www.dddprintingworld.com/pages/printing-collapsible-lightsabers-and-swords
)

Note: Assembled 3mf file for reference only

Printed with [3D Fuel Cobalt Blue and Silver Pro PLA](https://www.3dfuel.com/collections/175ppla)

Printed on the [Muldex]( https://github.com/3dprintingworld/MULDEX) rep-rap IDEX printer.

**Master Sword Versions**
[Print-N-Place](https://thangs.com/3dprintingworld/Collapsing-Master-Sword-Printnplace-34953)
[Dual Extrusion]( https://thangs.com/3dprintingworld/Collapsing-Mastersword-Duel-Extrusion-36377)
[Three Color](https://thangs.com/3dprintingworld/Collapsing-Master-Sword-3-Color-36466)

_Note: Assembly model for reference only._
____
Having troubles printing or want to show off your prints?  Join our Facebook [Group.](https://www.facebook.com/groups/1390970855008168) 

Collapsing Master Sword with Replaceable Blade

MASTER SWORD-2PCS-ASSY.3mf

3D printing accessories for the Gridfinity modular workshop system - store tools, nozzles, and more!

Gridfinity is the ultimate organizer for your whole workshop! Learn more at 
Find more Gridfinity accessories at https://bit.ly/3E2NxnZ

Parametric source files: 
- Caddy: https://a360.co/3KzVx2a
- Bottle Holder: https://a360.co/3LVjAsC
- Magigoo Holder: https://a360.co/3KzVEe6
- Nozzle Holder: https://a360.co/3KxGS7y
- Volcano Nozzle Holder: https://a360.co/3JLhKJz
- Revo Nozzlebreak Holder: https://a360.co/3xmVPpk
- Glue Sticc Holder: https://a360.co/3vapCiq

This assortment of 3D printer organizers is perfect for printing what you love to print - accessories for your printer!

**3D Printer Caddy**: Puts emergency supplies within reach! Holds scraper, nippers, tweezers, acupuncture needles, brass brush, adjustable wrench, and nozzle wrench

**Bottle Holder**: Designed to hold Nano Polymer high-temperature bed treatment, but also fits many small spray bottles. Bottles should not shake loose.

**Dual Bulk Nozzle Holder**: Holds eight copies of two different nozzle sizes. Can stack when loaded with E3D or Creality-style nozzles.

**Quad Revo Holder**: Holds four E3D RapidChange Revo nozzle-heatbreak nozzlebreaks. Can stack.

**Triple Volcano Holder**: Holds three extended E3D-style holders, like those included with the Anycubic Vyper and Kobra. Can stack.

**Glue Stick Holder**: Holds multiple sizes of icky sticky horsey bois, particularly Elmer's small and regular, and Kores.

**Magigoo Holder**: Holds four-piece Magigoo bed treatment assortment pack, and should not allow them to jiggle loose.

**Gridfinity Tips!**
- No brims or support required! 
- Use any filament with an 0.6mm or smaller nozzle. 
- Wider bins can curl, so maximize your bed adhesion if you're going big!
- All storage blocks are compatible with all baseplates!
- Most storage blocks are stackable!
- You can add 6x2mm magnets to the corners! They won't magnetize the contents.
- You can also use M3 screws in the corners. 

Gridfinity 3D Printing Bundle for Nerds

3D Printer Caddy.stl

Pen, pencil, and marker storage blocks for the Gridfinity modular workshop storage system - multiple options to fit your machine shop!

Gridfinity is the ultimate organizer for your whole workshop! Learn more at 
Find more Gridfinity accessories at https://bit.ly/3E2NxnZ

Parametric source files: 
- Regular Version: https://a360.co/37EP2we
- Chisel Version: https://a360.co/3E49liU
- EXTRA THICCCCCC: https://a360.co/3jqmzx4

These holders were designed to securely store Sharpie markers, but should fit many other brands of markers and other roughly marker-shaped objects. I won't judge, you do you.

These are tall enough to keep the pens from falling out, but securing with magnets or screws is **strongly** recommended!

**Regular version**: Fits standard Sharpie markers and other round, slim objects with a diameter of 12mm or less, like brushes and test tubes.

**Chisel version**: Fits chisel-tip Sharpies, paint pens, and other stuff with a cross-section that fits a 16x22mm ellipse.

**Magnum version**: Fits the girthiest of Sharpies and other extra-thicc 27mm rods. Careful where you point that thing.

**Gridfinity Tips!**
- No brims or support required! 
- Use any filament with an 0.6mm or smaller nozzle. 
- Wider bins can curl, so maximize your bed adhesion if you're going big!
- All storage blocks are compatible with all baseplates!
- Most storage blocks are stackable!
- You can add 6x2mm magnets to the corners! They won't magnetize the contents.
- You can also use M3 screws in the corners. 

Gridfinity Pen, Pencil, and Marker Holders

Sharpie Holder, Chisel.stl

Stash your measuring bois on your Gridfinity modular workshop storage system, Excalibur style.

Gridfinity is the ultimate organizer for your whole workshop! Learn more at  
Find more Gridfinity accessories at https://bit.ly/3E2NxnZ

Parametric source file: 
https://a360.co/3KZAXs6

This holder stores a Mitutoyo Absolute Digimatic Series 500 caliper and a pair of SR44 batteries in a bare minimum of desk space. By sticking the caliper straight up, the contoured socket protects the jaws from damage and fits 6", 12", and all sizes.

This block has a high center of gravity, so I strongly recommend mounting it to [a weighted baseplate](https://thangs.com/designer/ZackFreedman/3d-model/Gridfinity%20Baseplates-60925?manualModelView=true) using magnets or screws!

**Gridfinity Tips!**
- All storage blocks are compatible with all baseplates!
- Most storage blocks are stackable!
- You can add 6x2mm magnets to the corners! They won't magnetize the contents.
- You can also use M3 screws in the corners. 

Gridfinity Caliper Holder

Update: I converted my remix to an STL mesh, and laid out both parts in a print-ready orientation.

======================

Remix with an added shoulder above the maze, to prevent the cap coming off before the entire maze is completed.

3D Maze Puzzle Box - Print-ready STL "Anti-Cheat" version

Glass-front open-top storage blocks for the Gridfinity modular workshop storage system - yes, real glass!

Gridfinity is the ultimate organizer for your whole workshop! Learn more at  
Find more Gridfinity accessories at https://bit.ly/3E2NxnZ

Parametric source file: 
https://a360.co/3v8mtzG

These modified divider bins have one wall replaced with a glass microscope slide! Glass is more scratch-resistant than acrylic, and microscope slides come pre-cut to size. 

Each bin is made of two parts, the Compartment and the Faceplate. You'll also need:
- 1x3" Microscope slides: https://amzn.to/3O6qjBO
- 2mm Repair Tape: https://amzn.to/3M1D9zF

How to assemble:
1. Apply two strips of tape to the microscope slides, touching the short edges.
2. Stick that slide to the faceplate.
3. Apply two strips of tape down the short sides of the faceplate, over the glass.
4. Apply a third strip along the bottom. It will curl a little around the bottom.
5. Slap that crap onto the divider bins. Press hard.

These are perfect for storing small parts, especially if you plan to stack 'em up. The big window makes it easy to check what's inside and monitor your supply levels.

The inner surface has a generous scoop to make retrieving parts easy, and the tab fits 12mm label-maker tape.

I've provided a selection of different divider counts, to give you OPTIONS! Because microscope slides are only available in one size, only 2-unit-wide bins are possible.

Brims and support are not required, and these can be printed in any filament with an 0.6mm or smaller nozzle. 

**Gridfinity Tips!**
- All storage blocks are compatible with all baseplates!
- Most storage blocks are stackable!
- You can add 6x2mm magnets to the corners! They won't magnetize the contents.
- You can also use M3 screws in the corners. 

Gridfinity Window Divider Bin

Window Box 2x1x6 3-Compartment.stl

**Collapsing Master Sword**
This Master Sword prints-n-place as just the hilt but extends in to a full sword. Its 250mm tall when printing but extends to 870mm long! The sword is designed to be printed with a .4mm nozzle so the blade is two shells thick. The line width should be set to .42mm.

**Master Sword Versions**
[Replaceable Blade]( https://thangs.com/3dprintingworld/Collapsing-Master-Sword-with-Replaceable-Blade-35659)
[Dual Extrusion]( https://thangs.com/3dprintingworld/Collapsing-Mastersword-Duel-Extrusion-36377)
[Three Color](https://thangs.com/3dprintingworld/Collapsing-Master-Sword-3-Color-36466)

**Scale**
If you must scale only scale Z or change your nozzle size to match a smaller scale nozzle. For example, you can use a .3 nozzle and scale it to 75%, .32mm line width.  This would make it roughly 190mm tall. 

**Print Settings**
I had issues printing this the first time, I would suggest everyone do print the test print which can be found [here](https://thangs.com/3dprintingworld/MASTER-SWORD-TEST-PRINT-35236)  I printed several of them to better tune the retraction at layer changes. My issue was the size of the layer seams were causing the blades to fuse. The test print is a total of 24mm high so I change retraction setting every 8mm.  Then I compare the changes until I achieve the best result. Each printer is going to be different but in my case I used a negative “extra restart” distance to reduce the size of the layer seam. 

Detailed printing instructions can be found on my [website]( https://www.dddprintingworld.com/pages/printing-collapsible-lightsabers-and-swords
)

Printed with [3D Fuel Cobalt Blue and Silver Pro PLA](https://www.3dfuel.com/collections/175ppla)

Printed on the [Muldex]( https://github.com/3dprintingworld/MULDEX) rep-rap IDEX printer.
___
**Support and Licensing**
If you would like to help support more free models please consider joining my Thangs [Membership](https://than.gs/u/35786?plans=true) 
To get permission to sell physical copies of my models, consider joining my [Patreon](https://www.patreon.com/3dprintingworld)



Collapsing Master Sword (Print-in-place)

MASTER SWORD-PNP.stl

MASTER_SWORD-PNP.3mf

Socket organizers and ratchet holders for the Gridfinity modular workshop storage system!

Gridfinity is the ultimate organizer for your whole workshop! Learn more at 
Find more Gridfinity accessories at https://bit.ly/3E2NxnZ

Parametric source files: 
- 1/4" Imperial holder: https://a360.co/37cdZPW
- 1/4" Metric holder: https://a360.co/3vgUAFq
- Mulwark ratchet holder: https://a360.co/3OiHhNJ

These holders store your socket sets and ratchet drivers. They orient the tools to make them easier to find and grab the bit you need!

**1/4" Imperial and Metric Holders**: Designed for Harbor Freight 10-piece 1/4"-socket kits, but should fit many others.

**1/4" Universal Holder**: Has ten 20mm-diameter slots. Note that this is five slots wide, while the Imperial and Metric versions are four slots wide.

**Mulwark Holder**: Fits the [Mulwark-brand low-profile ratchet driver](https://amzn.to/3v6BPEw), the 20pc bit kit, and has slots for 13 more hex bits. I strongly recommend buying the bit kit - a low-profile ratchet needs low-profile bits!

Print the ones that work with your stuff!

**Gridfinity Tips!**
- No brims or support required! 
- Use any filament with an 0.6mm or smaller nozzle. 
- Wider bins can curl, so maximize your bed adhesion!
- All storage blocks are compatible with all baseplates!
- Most storage blocks are stackable!
- You can add 6x2mm magnets to the corners! They won't magnetize the contents.
- You can also use M3 screws in the corners!

Gridfinity Ratchet + Socket Holders

Socket Holder, Metric, Non-Stackable.stl

Socket Holder, 0.25in, Universal, Non-Stackable.stl

**Collapsing Master Sword** 
_(Replaceable Blade Dual Extrusion Version)_

This is the same as the single extruder version but the hilt is separated into separate files for dual extrusion.  Only the hilt files are here, please see the [Single Extruder Version](https://thangs.com/3dprintingworld/Collapsing-Master-Sword-with-Replaceable-Blade-35659) for the blades and print instructions.

Detailed printing instructions can be found on my [website]( https://www.dddprintingworld.com/pages/printing-collapsible-lightsabers-and-swords
)

Printed with [3D Fuel Cobalt Blue and Silver Pro PLA](https://www.3dfuel.com/collections/175ppla)

Printed on the [Muldex](https://github.com/3dprintingworld/MULDEX) rep-rap IDEX printer.

**Master Sword Versions**
[Print-N-Place](https://thangs.com/3dprintingworld/Collapsing-Master-Sword-Printnplace-34953)
[Replaceable Blade]( https://thangs.com/3dprintingworld/Collapsing-Master-Sword-with-Replaceable-Blade-35659)
[Three Color](https://thangs.com/3dprintingworld/Collapsing-Master-Sword-3-Color-36466)
____
Having troubles printing or want to show off your prints?  Join our Facebook [Group.](https://www.facebook.com/groups/1390970855008168) 

Collapsing Master Sword (Dual Extrusion)

MASTER SWORD-2PCS-ASSY.stl

This is a test print for the Collapsing Katana.  If you can print it with NOTHING attaching the rings together, then you should be able to successfully print the full sword.


The test print is a total of 24mm high so I change settings every 8mm(3x)  then compare the changes until I achieve the best result. The settings that will have the most impact are; flowrate, retraction distance/speed, coast, wipe, and extra restart distance.  You may also try; seam location, speed, temperature, and z-hop.


I have detailed instructions on [how to print collapsing swords](https://www.dddprintingworld.com/pages/printing-collapsible-lightsabers-and-swords) on my website.
___
**Support and Licensing**
If you would like to help support more free models please consider joining my Thangs [Membership](https://than.gs/u/35786?plans=true) 
To get permission to sell physical copies of my models by joining my [Patreon](https://www.patreon.com/3dprintingworld)


Katana Test Print

KATANA-TEST PRINT.stl

This is an updated version of my original Maze Puzzle box. This one works better and makes it impossible to cheat when close to the end of the maze.

This is an STL file with the parts set side-by-side, ready to 3D print!

3D Printable Maze Puzzle Box - STL File.stl

This is a customizable rolling storage bin system.

**Learn More**

*Introduction*
https://youtu.be/Cm5bByFYJKk

*More Bins*
https://youtu.be/ak8NoDQWSmo

*Even More Bins*
https://youtu.be/tUDJG0Tqd8U

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4745676.

Rolling Storage Box

Assembled_and_Open.3mf

Cap.stl

Rolling_Storage_Box_-_All_Parts.step

TPU_Strap.stl

This is a test print for the collapsing swords and Light Sabers.  If you can print thing without the rings sticking together then you should be able to successfully print the full sword. 

The test print is a total of 24mm high so I change retraction settings every 8mm.  Then I compare the changes until I achieve the best result. 

Each printer is going to be different but in my case I used a negative “extra restart” distance to reduce the size of the layer seam. Retraction distance/speed, wipe, coast, temperature, speed may also have an effect. 


Sword-Saber Test Print

This is a test print for the collapsing swords and Light Sabers.  If you can print thing without the rings sticking together then you should be able to successfully print the full sword. 

Maker-favorite screwdriver storage blocks for the Gridfinity modular workshop storage system - multiple options to fit your machine shop!

Gridfinity is the ultimate organizer for your whole workshop! Learn more at 
Find more Gridfinity accessories at https://bit.ly/3E2NxnZ

Parametric source files: 
- ES121 Holder: https://a360.co/3KLQziI
- Gen 1 Holder: https://a360.co/3rj30Li
- Gen 2 Holder: https://a360.co/3jxCNVb

These holders store the popular, high-quality iFixit Mako screwdriver kit, the old-skool iFixit screwdriver set, and the ES121 open-hardware electric screwdriver. Open-source screwdriver, what a time to be alive.

Print the ones that work with your stuff!

**Gridfinity Tips!**
- No brims or support required! 
- Use any filament with an 0.6mm or smaller nozzle. 
- Wider bins can curl, so maximize your bed adhesion if you're going big!
- All storage blocks are compatible with all baseplates!
- Most storage blocks are stackable!
- You can add 6x2mm magnets to the corners! They won't magnetize the contents.
- You can also use M3 screws in the corners.

Gridfinity iFixit Mako + ES121 Screwdriver Holders

iFixit Driver Set Gen 2 Holder.stl

This is a collapsing sword designed to be printed as one part. Its only 142mm high when printed but expands to over 860mm in total length! The sword is designed to be printed with a ,4mm nozzle, the blade will be two shells thick.

There is a [test print](https://thangs.com/3dprintingworld/SwordSaber-Test-Print-23601) file. If this works, you shouldn't have an issue. If it fuses together, I would suggest adjusting your cost and wipe settings.  

Detailed printing instructions can be found on my [website]( https://www.dddprintingworld.com/pages/printing-collapsible-lightsabers-and-swords
)

For more info on how to print this, I made a trouble shooting video. https://youtu.be/YQV4PYJPhx0

If you want to throw a little support my way, please follow the affiliate links to the filament I used to make this swords.
Silver: https://amzn.to/2W3Z1Gh
Pink: https://amzn.to/3AZngnL

**Collapsing Swords**
[Master Sword]( https://thangs.com/3dprintingworld/Collapsing-Master-Sword-with-Replaceable-Blade-35659)
[Katana]( https://thangs.com/3dprintingworld/Collapsing-Katana-22696)
[Jian]( https://thangs.com/3dprintingworld/Collapsing-Jian-24803)
[Board Sword]( https://thangs.com/3dprintingworld/Collapsing-Broadsword-24236)
[Dagger]( https://thangs.com/3dprintingworld/Collapsing-Dagger-24805)
___
**Support and Licensing**
If you would like to help support more free models please consider joining my Thangs [Membership](https://than.gs/u/35786?plans=true) 
To get permission to sell physical copies of my models by joining my [Patreon](https://www.patreon.com/3dprintingworld)


Collapsing Pirate Sword

This is a collapsing sword designed to be printed as one part. Its only 142mm high when printed but expands to over 860mm in total length! The sword is designed to be printed with a ,4mm nozzle, the blade will be two shells thick.

There is a file named "test print". If this works, you shouldn't have an issue. If it fuses together, I would suggest adjusting your cost and wipe settings.  For more info on how to print this, I made a trouble shooting [video.]video

If you want to throw a little support my way, please follow the affiliate links to the filament I used to make this swords.
[Silver Filament][silver]
[Pink Filament][Pink]

[silver]:https://amzn.to/2W3Z1Gh
[Pink]:https://amzn.to/3AZngnL
[Video]:https://youtu.be/YQV4PYJPhx0



COLLAPSING PIRATE SWORD

The One Can Cooler! Holds exactly one 12oz or 16oz can (and ice).

Files included shell, insert, lid, and plug for 3D printing 12oz cooler, and the same set for 16oz. Support free, but couldn't hurt to use "Touch Buildplate" on the outer shell to support the drain overhang.

What's your favorite drink?

3D Print: One Can Cooler

12oz Cooler Complete.STEP

This is a mix of the [Impossible Gear Fidget](https://social.thangs.com/m/700537) and the [Planetary Gear Demo]( https://thangs.com/designer/3dprintingworld/3d-model/Mini%20Planetary%20Gear%20Print-in-Place%20Demo-50395).  This fidget uses planetary gears, it’s a great way to better understand how they work. 

**Demonstration**
If you hold the carrier(middle gear) and turn the sun(top gear), you get at 3:1 speed reduction.  This ratio is a result of  the 36 teeth on the ring gear divided by the 12 teeth on planet gears. If you hold the ring(bottom gear) and turn the sun(top gear), you get a 1:4 speed reduction on the carrier(middle gear). The is because the much larger diameter ring gear is moving faster than the smaller sun gear. The equation works out to be the 36 teeth of the ring gear divided by the 12 teeth of the planet gear plus 1. If you hold the sun gear and spin the ring gear and the carrier, there is no reduction and it acts like a bearing

No supports!

Printed on the [Mulcore]( https://github.com/3dprintingworld/Mulcore)

___
**Support and Licensing**
If you would like to help support more free models please consider joining my Thangs [Membership](https://than.gs/u/35786?plans=true) 
To get permission to sell physical copies of my models by joining my [Patreon](https://www.patreon.com/3dprintingworld)




The Impossible Planetary Gear Fidget

This is a mix of the [Impossible Gear Fidget](https://social.thangs.com/m/700537) and the [Planetary Gear Demo]( https://thangs.com/designer/3dprintingworld/3d-model/Mini%20Planetary%20Gear%20Print-in-Place%20Demo-50395).  This fidget uses planetary gears, it’s a great way to better understand how they work. 

**Demonstration**
If you hold the carrier(middle gear) and turn the sun(top gear), you get at 3:1 speed reduction.  This ratio is a result of  the 36 teeth on the ring gear divided by the 12 teeth on planet gears. If you hold the ring(bottom gear) and turn the sun(top gear), you get a 1:4 speed reduction on the carrier(middle gear). The is because the much larger diameter ring gear is moving faster than the smaller sun gear. The equation works out to be the 36 teeth of the ring gear divided by the 12 teeth of the planet gear plus 1. If you hold the sun gear and spin the ring gear and the carrier, there is no reduction and it acts like a bearing

No supports!

Printed on the [Mulcore]( https://github.com/3dprintingworld/Mulcore)

**Support and Licensing**
If you would like to help support more free models, or get permission to sell physical copies of my models, consider joining my [Patreon]( https://www.patreon.com/3dprintingworld)


Hobbies & Games

Most Popular of All Time

Categories

Popular

Personalize

Trending