Straighten out your workshop with Gridfinity modular storage - deploy these plates anywhere you need some order!

Gridfinity is the ultimate organizer for your whole workshop! Learn more at 
Find more Gridfinity accessories at https://bit.ly/3E2NxnZ

Parametric source files: 
- Frame: https://a360.co/3ccHbsg
- Weighted Plate: https://a360.co/3uCJ2gR

The foundation of every Gridfinity setup is a baseplate, and these let you drop storage where you need it most.

**Frame**: The absolutely minimal no-frills baseplate. No room for screws or magnets, but saves filament and headroom. If your storage unit is on a steel surface, you can still put magnets in the storage blocks to keep them from sliding.

**Weighted**: Heavy, sturdy baseplate perfect for desktops, shelves, and other places where knocking stuff over is a big problem. 

Secure blocks permanently with [M3 screws,](https://amzn.to/37IaXTg) or temporarily with [6x2mm magnets](https://amzn.to/37Ihopq). Add [rubber feet](https://amzn.to/3LZv4v5) to keep the whole shebang from sliding, and [metal tire weights ](https://amzn.to/3uAzH9f)to drop the center of gravity and prevent wipeouts. You don't need to install every magnet, foot, and weight! Just use enough for your needs.

A Prusa i3 Mk3 can print up to a 5x5 grid. No matter what you use, make sure your bed adhesion and release is dialed in - these love to curl, and their high surface area can make them challenging to remove.

**Gridfinity Tips!**
- No brims or support required! 
- Use any filament with an 0.6mm or smaller nozzle. 
- Wider plates can curl, so maximize your bed adhesion if you're going big!
- All storage blocks are compatible with all baseplates!
- Most storage blocks are stackable!
- You can add 6x2mm magnets to the corners! They won't magnetize the contents.
- You can also use M3 screws in the corners.

Gridfinity Baseplates

Weighted Baseplate 3x2.stl

Frame 1x4.stl

Frame 1x5.stl

Frame 1x6.stl

Frame 1x7.stl

Frame 2x2.stl

Frame 2x3.stl

Frame 1x2.stl

Frame 1x3.stl

Frame 2x7.stl

Frame 3x3.stl

Frame 3x4.stl

Frame 3x5.stl

Frame 3x6.stl

Frame 3x7.stl

Frame 4x4.stl

Frame 4x5.stl

Frame 4x6.stl

Frame 4x7.stl

Frame 5x5.stl

Frame 5x6.stl

Frame 5x7.stl

Frame 6x6.stl

Frame 6x7.stl

Frame 2x5.stl

Frame 2x6.stl

Weighted Baseplate 1x3.stl

Weighted Baseplate 1x4.stl

Weighted Baseplate 1x5.stl

Weighted Baseplate 1x6.stl

Weighted Baseplate 1x7.stl

Weighted Baseplate 2x2.stl

Weighted Baseplate 1x1 (super cute).stl

Weighted Baseplate 1x2.stl

Weighted Baseplate 2x4.stl

Weighted Baseplate 2x5.stl

Weighted Baseplate 3x6.stl

Weighted Baseplate 3x7.stl

Weighted Baseplate 4x4.stl

Weighted Baseplate 4x5.stl

Weighted Baseplate 4x6.stl

Weighted Baseplate 4x7.stl

Weighted Baseplate 5x5.stl

Weighted Baseplate 5x6.stl

Weighted Baseplate 5x7.stl

Weighted Baseplate 6x6.stl

Weighted Baseplate 6x7.stl

Weighted Baseplate 7x7.stl

Weighted Baseplate 2x7.stl

Weighted Baseplate 3x3.stl

Weighted Baseplate 3x4.stl

Weighted Baseplate 3x5.stl

Versatile open-top storage blocks for the Gridfinity modular workshop storage system - multiple sizes for infinite options!

Gridfinity is the ultimate organizer for your whole workshop! Learn more at  
Find more Gridfinity accessories at https://bit.ly/3E2NxnZ

Parametric source file: https://a360.co/3vbu9B5

These are perfect for storing small parts and long, thin objects like needle files, and you can stack them as high as you want! The inner surface has a generous scoop to make retrieving parts easy, and the tab fits 12mm label-maker tape.

I've provided a selection of different sizes and divider counts, to give you OPTIONS! Note that none of the compartment sizes overlap - there isn't a two-compartment 4x1 bin because you can just use two one-compartment 2x1 bins.

Dimensions in file names are Width x Depth x Height. Width and Depth units are 42mm grid slots, Height is in 7mm units. A Prusa i3 Mk3S can fit a five-unit-wide bin on its plate.

Note that two-unit-high bins don't have labels - they would cut too far into the usable storage area.

Brims and support are not required, and these can be printed in any filament with an 0.6mm or smaller nozzle. Wider bins can curl, so maximize your bed adhesion if you're going big!

**Gridfinity Tips!**
- All storage blocks are compatible with all baseplates!
- Most storage blocks are stackable!
- You can add 6x2mm magnets to the corners! They won't magnetize the contents.
- You can also use M3 screws in the corners. 

Gridfinity Divider Bins

Divider Box 2x1x6 5-Compartment.stl

Safely grab the right tool with the Gridfinity modular workshop storage system!

Gridfinity is the ultimate organizer for your whole workshop! Learn more at https://www.youtube.com/watch?v=ra_9zU-mnl8
Find more Gridfinity accessories at https://bit.ly/3E2NxnZ

Parametric source files: 
- Nipper Holder: https://a360.co/37jchw3
- Stripper Holder: https://a360.co/3Erq2oV

These racks pack tons of hand tools into a small area, positioned so you can safely see and grab the business ends. These work great for nippers, flush cutters, wire strippers, pliers, scissors, crimpers, nibblers, cutters, and punch-down tools.

*These storage blocks are extra-big and tend to curl! Use a brim and ensure good bed adhesion.* 

**Nipper Holder**: Holds six tools about 80mm from handle to handle. If the tool is spring-loaded, the undercut will keep it from falling out. This can be mounted sideways to store five tools.

**Stripper Holder**: Holds two wire strippers or other long, slim hand tools up to 18mm thicc. I've prepared two sizes - 200mm is your usual multi-hole wire stripper, and 160mm fits many crimpers and termination tools. Both should fit on most printers.

**Gridfinity Tips!**
- Use any filament with an 0.6mm or smaller nozzle. 
- All storage blocks are compatible with all baseplates!
- Most storage blocks are stackable!
- You can add 6x2mm magnets to the corners! They won't magnetize the contents.
- You can also use M3 screws in the corners.

Gridfinity Nippers + Strippers + Pliers Racks

Nipper Holder x6.stl

Pointy boi storage for the Gridfinity modular workshop storage system - saves space and delicate fingies!

Gridfinity is the ultimate organizer for your whole workshop! Learn more at 
Find more Gridfinity accessories at https://bit.ly/3E2NxnZ

Parametric source files: 
- Pick Rack: https://a360.co/3JCOrIS
- Chonk Rack: https://a360.co/3xgYhO9
- Tweezer Rack: https://a360.co/3uxC0dd

These racks store long, pointy objects at an angle... but angle the business ends away from pokey fingers.

These are all two-part models. Print an Upper and a Lower and glue 'em together.

- The Pick Rack is perfect for slender tools like picks and files.
- The Chonk Rack is for thiccer tools (hey-o) like scrapers, forceps, and spring tweezers.
-  The Twizzles Rack holds tweezers. I call them twizzles because I think it's funny.

The Twizzles Rack Upper is the only piece that needs support.

**Gridfinity Tips!**
- No brims or support required! 
- Use any filament with an 0.6mm or smaller nozzle. 
- Wider bins can curl, so maximize your bed adhesion if you're going big!
- All storage blocks are compatible with all baseplates!
- Most storage blocks are stackable!
- You can add 6x2mm magnets to the corners! They won't magnetize the contents.
- You can also use M3 screws in the corners.

Gridfinity Pick + Tweezer Racks

Illustration! Don't print!!

3D printing accessories for the Gridfinity modular workshop system - store tools, nozzles, and more!

Gridfinity is the ultimate organizer for your whole workshop! Learn more at 
Find more Gridfinity accessories at https://bit.ly/3E2NxnZ

Parametric source files: 
- Caddy: https://a360.co/3KzVx2a
- Bottle Holder: https://a360.co/3LVjAsC
- Magigoo Holder: https://a360.co/3KzVEe6
- Nozzle Holder: https://a360.co/3KxGS7y
- Volcano Nozzle Holder: https://a360.co/3JLhKJz
- Revo Nozzlebreak Holder: https://a360.co/3xmVPpk
- Glue Sticc Holder: https://a360.co/3vapCiq

This assortment of 3D printer organizers is perfect for printing what you love to print - accessories for your printer!

**3D Printer Caddy**: Puts emergency supplies within reach! Holds scraper, nippers, tweezers, acupuncture needles, brass brush, adjustable wrench, and nozzle wrench

**Bottle Holder**: Designed to hold Nano Polymer high-temperature bed treatment, but also fits many small spray bottles. Bottles should not shake loose.

**Dual Bulk Nozzle Holder**: Holds eight copies of two different nozzle sizes. Can stack when loaded with E3D or Creality-style nozzles.

**Quad Revo Holder**: Holds four E3D RapidChange Revo nozzle-heatbreak nozzlebreaks. Can stack.

**Triple Volcano Holder**: Holds three extended E3D-style holders, like those included with the Anycubic Vyper and Kobra. Can stack.

**Glue Stick Holder**: Holds multiple sizes of icky sticky horsey bois, particularly Elmer's small and regular, and Kores.

**Magigoo Holder**: Holds four-piece Magigoo bed treatment assortment pack, and should not allow them to jiggle loose.

**Gridfinity Tips!**
- No brims or support required! 
- Use any filament with an 0.6mm or smaller nozzle. 
- Wider bins can curl, so maximize your bed adhesion if you're going big!
- All storage blocks are compatible with all baseplates!
- Most storage blocks are stackable!
- You can add 6x2mm magnets to the corners! They won't magnetize the contents.
- You can also use M3 screws in the corners. 

Gridfinity 3D Printing Bundle for Nerds

3D Printer Caddy.stl

Pen, pencil, and marker storage blocks for the Gridfinity modular workshop storage system - multiple options to fit your machine shop!

Gridfinity is the ultimate organizer for your whole workshop! Learn more at 
Find more Gridfinity accessories at https://bit.ly/3E2NxnZ

Parametric source files: 
- Regular Version: https://a360.co/37EP2we
- Chisel Version: https://a360.co/3E49liU
- EXTRA THICCCCCC: https://a360.co/3jqmzx4

These holders were designed to securely store Sharpie markers, but should fit many other brands of markers and other roughly marker-shaped objects. I won't judge, you do you.

These are tall enough to keep the pens from falling out, but securing with magnets or screws is **strongly** recommended!

**Regular version**: Fits standard Sharpie markers and other round, slim objects with a diameter of 12mm or less, like brushes and test tubes.

**Chisel version**: Fits chisel-tip Sharpies, paint pens, and other stuff with a cross-section that fits a 16x22mm ellipse.

**Magnum version**: Fits the girthiest of Sharpies and other extra-thicc 27mm rods. Careful where you point that thing.

**Gridfinity Tips!**
- No brims or support required! 
- Use any filament with an 0.6mm or smaller nozzle. 
- Wider bins can curl, so maximize your bed adhesion if you're going big!
- All storage blocks are compatible with all baseplates!
- Most storage blocks are stackable!
- You can add 6x2mm magnets to the corners! They won't magnetize the contents.
- You can also use M3 screws in the corners. 

Gridfinity Pen, Pencil, and Marker Holders

Sharpie Holder, Chisel.stl

Stash your measuring bois on your Gridfinity modular workshop storage system, Excalibur style.

Gridfinity is the ultimate organizer for your whole workshop! Learn more at  
Find more Gridfinity accessories at https://bit.ly/3E2NxnZ

Parametric source file: 
https://a360.co/3KZAXs6

This holder stores a Mitutoyo Absolute Digimatic Series 500 caliper and a pair of SR44 batteries in a bare minimum of desk space. By sticking the caliper straight up, the contoured socket protects the jaws from damage and fits 6", 12", and all sizes.

This block has a high center of gravity, so I strongly recommend mounting it to [a weighted baseplate](https://thangs.com/designer/ZackFreedman/3d-model/Gridfinity%20Baseplates-60925?manualModelView=true) using magnets or screws!

**Gridfinity Tips!**
- All storage blocks are compatible with all baseplates!
- Most storage blocks are stackable!
- You can add 6x2mm magnets to the corners! They won't magnetize the contents.
- You can also use M3 screws in the corners. 

Gridfinity Caliper Holder

Glass-front open-top storage blocks for the Gridfinity modular workshop storage system - yes, real glass!

Gridfinity is the ultimate organizer for your whole workshop! Learn more at  
Find more Gridfinity accessories at https://bit.ly/3E2NxnZ

Parametric source file: 
https://a360.co/3v8mtzG

These modified divider bins have one wall replaced with a glass microscope slide! Glass is more scratch-resistant than acrylic, and microscope slides come pre-cut to size. 

Each bin is made of two parts, the Compartment and the Faceplate. You'll also need:
- 1x3" Microscope slides: https://amzn.to/3O6qjBO
- 2mm Repair Tape: https://amzn.to/3M1D9zF

How to assemble:
1. Apply two strips of tape to the microscope slides, touching the short edges.
2. Stick that slide to the faceplate.
3. Apply two strips of tape down the short sides of the faceplate, over the glass.
4. Apply a third strip along the bottom. It will curl a little around the bottom.
5. Slap that crap onto the divider bins. Press hard.

These are perfect for storing small parts, especially if you plan to stack 'em up. The big window makes it easy to check what's inside and monitor your supply levels.

The inner surface has a generous scoop to make retrieving parts easy, and the tab fits 12mm label-maker tape.

I've provided a selection of different divider counts, to give you OPTIONS! Because microscope slides are only available in one size, only 2-unit-wide bins are possible.

Brims and support are not required, and these can be printed in any filament with an 0.6mm or smaller nozzle. 

**Gridfinity Tips!**
- All storage blocks are compatible with all baseplates!
- Most storage blocks are stackable!
- You can add 6x2mm magnets to the corners! They won't magnetize the contents.
- You can also use M3 screws in the corners. 

Gridfinity Window Divider Bin

Window Box 2x1x6 3-Compartment.stl

Socket organizers and ratchet holders for the Gridfinity modular workshop storage system!

Gridfinity is the ultimate organizer for your whole workshop! Learn more at 
Find more Gridfinity accessories at https://bit.ly/3E2NxnZ

Parametric source files: 
- 1/4" Imperial holder: https://a360.co/37cdZPW
- 1/4" Metric holder: https://a360.co/3vgUAFq
- Mulwark ratchet holder: https://a360.co/3OiHhNJ

These holders store your socket sets and ratchet drivers. They orient the tools to make them easier to find and grab the bit you need!

**1/4" Imperial and Metric Holders**: Designed for Harbor Freight 10-piece 1/4"-socket kits, but should fit many others.

**1/4" Universal Holder**: Has ten 20mm-diameter slots. Note that this is five slots wide, while the Imperial and Metric versions are four slots wide.

**Mulwark Holder**: Fits the [Mulwark-brand low-profile ratchet driver](https://amzn.to/3v6BPEw), the 20pc bit kit, and has slots for 13 more hex bits. I strongly recommend buying the bit kit - a low-profile ratchet needs low-profile bits!

Print the ones that work with your stuff!

**Gridfinity Tips!**
- No brims or support required! 
- Use any filament with an 0.6mm or smaller nozzle. 
- Wider bins can curl, so maximize your bed adhesion!
- All storage blocks are compatible with all baseplates!
- Most storage blocks are stackable!
- You can add 6x2mm magnets to the corners! They won't magnetize the contents.
- You can also use M3 screws in the corners!

Gridfinity Ratchet + Socket Holders

Socket Holder, Metric, Non-Stackable.stl

Socket Holder, 0.25in, Universal, Non-Stackable.stl

Maker-favorite screwdriver storage blocks for the Gridfinity modular workshop storage system - multiple options to fit your machine shop!

Gridfinity is the ultimate organizer for your whole workshop! Learn more at 
Find more Gridfinity accessories at https://bit.ly/3E2NxnZ

Parametric source files: 
- ES121 Holder: https://a360.co/3KLQziI
- Gen 1 Holder: https://a360.co/3rj30Li
- Gen 2 Holder: https://a360.co/3jxCNVb

These holders store the popular, high-quality iFixit Mako screwdriver kit, the old-skool iFixit screwdriver set, and the ES121 open-hardware electric screwdriver. Open-source screwdriver, what a time to be alive.

Print the ones that work with your stuff!

**Gridfinity Tips!**
- No brims or support required! 
- Use any filament with an 0.6mm or smaller nozzle. 
- Wider bins can curl, so maximize your bed adhesion if you're going big!
- All storage blocks are compatible with all baseplates!
- Most storage blocks are stackable!
- You can add 6x2mm magnets to the corners! They won't magnetize the contents.
- You can also use M3 screws in the corners.

Gridfinity iFixit Mako + ES121 Screwdriver Holders

iFixit Driver Set Gen 2 Holder.stl

Mount storage right to your printer with the Gridfinity modular workshop storage system - whatever machine you use!

Gridfinity is the ultimate organizer for your whole workshop! Learn more at 
Find more Gridfinity accessories at https://bit.ly/3E2NxnZ

Parametric source files: 
- Anycubic Sidecar: https://a360.co/3xonYw4
- Anycubic Top: https://a360.co/3jy22GN
- Lulzbot: https://a360.co/3xobNzx
- Prusa: https://a360.co/3Jzfp47
- Snapmaker: https://a360.co/37Om65m
- E3D Toolchanger: https://a360.co/3rlmn6K

These brackets mount to your 3D printer and allow you to put Gridfinity storage blocks right where you need them! These work especially well for the [Gridfinity 3D-printer accessory kit](https://bit.ly/3jtTfWu).

If you need more adjacent slots, just print multiple baseplates and butt them up against each other. *I STRONGLY recommend magnets or screws so you don't knock stuff into your printer!*

**Anycubic Vyper/Kobra**: Also fits any printer made of extrusion with 6mm slots. Mount to your printer's frame with [M5 hammer nuts for 6mm slots](https://amzn.to/3jzbOZb) and [M5x12mm countersunk screws](https://amzn.to/3xoGLHV). Remember to measure countersunk screws from the TOP OF THE HEAD!

The **sidecar** baseplate mounts to the base frame, parallel with the floor, a lot like the included filament holder. The **top-mount** baseplate mounts on the Z axis crossbeam or base frame. *Make sure the gantry, extruder, and plate don't collide with your Gridfinity!*

**Lulzbot**: Fits the upward-facing edges of the top crossbars. This one is a real pain in the butt to install.

**Prusa**: Slides on over the steel frame, no fasteners required. *THE BASEPLATE AND EXTRUDER MUST BE ON OPPOSITE SIDES OF THE FRAME!*

**Snapmaker**: Mount to the optional enclosure with [M5 hammer nuts for 6mm slots](https://amzn.to/3jzbOZb) and [M5x12mm countersunk screws](https://amzn.to/3xoGLHV). Remember to measure countersunk screws from the TOP OF THE HEAD! I didn't make one for the printer itself, sorry!

**Toolchanger**: Mount to the top of the printer with three button head M3x5 screws. *Don't use longer screws! They won't fit!*

**Gridfinity Tips!**
- No brims or support required! 
- Use any filament with an 0.6mm or smaller nozzle. 
- Wider bins can curl, so maximize your bed adhesion if you're going big!
- All storage blocks are compatible with all baseplates!
- Most storage blocks are stackable!
- You can add 6x2mm magnets to the corners! They won't magnetize the contents.
- You can also use M3 screws in the corners.

Gridfinity Printer-Mounted Baseplates

Anycubic Baseplate, Sidecar.stl

CNC bit storage blocks for the Gridfinity modular workshop storage system - multiple options to fit your machine shop!

Gridfinity is the ultimate organizer for your whole workshop! Learn more at 
Find more Gridfinity accessories at https://bit.ly/3E2NxnZ

Parametric source files: 
- Jewel Case: https://a360.co/3Jw4Bnd
- Bulk Holder: https://a360.co/37IQCgV
- Tubes: https://a360.co/3rFWH4X

These holders securely store CNC tools, drill bits, and other things with 1/8", 1/4", and 3mm shanks.

The 1/8" and 1/4" Bulk versions hold up to 77 and 21 bits, respectively. These point the bits straight up, so you can't stack on top! Be careful not to hurt yourself!

The Tube version holds 12 bits in their protective packages. You can stack other blocks on top of this.

The Jewel Insert version holds four detachable sleeves from snap-together jewel case packaging. These usually hold 10 bits. You can stack other blocks on top of this.

**Gridfinity Tips!**
- No brims or support required! 
- Use any filament with an 0.6mm or smaller nozzle. 
- Wider bins can curl, so maximize your bed adhesion if you're going big!
- All storage blocks are compatible with all baseplates!
- Most storage blocks are stackable!
- You can add 6x2mm magnets to the corners! They won't magnetize the contents.
- You can also use M3 screws in the corners. 

Gridfinity CNC Tool Holders

CNC Tool Holder, Tubes.stl

Designed to work with storage modules from the Gridfinity system by Zack Freedman.

These racks are stackable, with small tabs to aid in both horizontal and vertical alignment.

I had these windowed divider bins in mind when i was designing this: https://thangs.com/designer/ZackFreedman/3d-model/Gridfinity%2520Window%2520Divider%2520Bin-60754


Gridfinity Wall Rack

rack.step

CNC collet storage blocks for the Gridfinity modular workshop storage system - they're both ER11 for now.

Gridfinity is the ultimate organizer for your whole workshop! Learn more at 
Find more Gridfinity accessories at https://bit.ly/3E2NxnZ

Parametric source files: 
- Stupid Version: https://a360.co/3JznS7x
- Non-Stupid Version: https://a360.co/3M0PDar

These bad boys hold CNC collets - I only have an ER11 Snapmaker, so that's what ya get.

**The stupid version** holds collets in their little yellow boxes.

**The non-stupid version** holds the collets without the boxes.

There's no reason to use the stupid version. Just remember to keep the collets nice and oiled to prevent rust.

**Gridfinity Tips!**
- No brims or support required! 
- Use any filament with an 0.6mm or smaller nozzle. 
- Wider bins can curl, so maximize your bed adhesion if you're going big!
- All storage blocks are compatible with all baseplates!
- Most storage blocks are stackable!
- You can add 6x2mm magnets to the corners! They won't magnetize the contents.
- You can also use M3 screws in the corners. 

Gridfinity Collet Holder Collet-ction

Collet Holder, ER11, Non-Stupid.stl

2x3x7.4mm Gridfinity Drawers.

Tested in PLA, printed with body cavity facing upwards and with only tiny supports between the gridfinity rows on a Elegoo Neptune 2 model.

Suggest minimal cubic infill (5-10%) with 3-4 outer walls.

 * Added drawer model with thicker walls.
* Refined drawer model for a better fit into the slots horizontally.
* Added two-compartment drawer model.
* Added drawer with a tighter horizontal fit.
* Added double-height drawer model.
* Added Minifinity drawer model.

* Organize your Gridfinity Drawers with Minifinity!
https://social.thangs.com/m/195636

Gridfinity concept by Zack Freedman

Gridfinity Drawers

Gridfinity_Drawers_2x3_Chest.stl

Gridfinity_Drawers_Drawer_Thicker.stl

Gridfinity_Drawers_Drawer_Thicker_Two_Compartment.stl

Gridfinity_Drawers_Drawer_Thicker_Tighter_Fit.stl

Gridfinity_Drawers_Drawer_Double_Height.stl

Drawers_Minifinity_4x6.stl

1x1 Gridfinity block for storing up to 10 USB devices as well as 3 Micro SD cards. Simple design set up for fast printing. 

Recommended settings are as follows:

Layer Height: .32mm
Walls: 3
Infill: 10% - 20% (depending on desire)
Supports: No

Drives will sit straight up and down but are intentionally a tiny bit loose - in my experience if they are tight in the socket you end up picking up the whole block instead of the drive you want.

____________________________________________

Find all of my Gridfinity models here:

https://thangs.com/search/%22--thingymaker9000gridfinity--%22?scope=all

--thingymaker9000gridfinity--

____________________________________________

If you find these or anything else I make useful, you can buy me a beer over here:

https://www.buymeacoffee.com/thingymaker9000

Enjoy!

Gridfinity USB & Micro SD Holder

1x1 Gridfinity block for storing up to 10 USB devices as well as 3 Micro SD cards. Simple design set up for fast printing. 

Recommended settings are as follows:

Layer Height: .32mm
Walls: 3
Infill: 10% - 20% (depending on desire)
Supports: No

A Gridfinity adapter is nothing more than the bottom mating portion with a flat top surface. This enables you to fasten whatever you want to a Gridfinity system without needing to 3d model anything specific. 

For example, if you already have a great case for your tool, just glue the tool case to an appropriately sized adapter and bam, now it's a Gridfinity case.

Also included in the download is the Fusion360 .f3d file.

Gridfinity Adapters

Gridfinity Adapter 5x5.stl

This is a 1x1 block for the Gridfinity system, which stores up to 9 full-size SD cards as well as 9 Micro SD cards.

I recommend printing this if you have a large amount of SD cards to store. This is not great for cards which you are using constantly, as it will get tedious to remove individual cards. This is dense storage for those of us who have lots of these cards and adapters lying around.

Print settings are as usual for my Gridfinity items:

Layer height: .24 - .32
Top / Bottom Layers + Walls: 3 - 4
Infill: 10% - 20%

Use the lower values for cheaper / faster prints; use the higher values for weightier / higher quality items. You get the idea.

____________________________________________

Find all of my Gridfinity models here:

https://thangs.com/search/%22--thingymaker9000gridfinity--%22?scope=all

--thingymaker9000gridfinity--

____________________________________________

If you find these or anything else I make useful, you can buy me a beer over here:

https://www.buymeacoffee.com/thingymaker9000

Enjoy!

Gridfinity 1x1 Dense 9 Full SD & 9 Micro SD Card Storage

This is a 1x1 block for the Gridfinity system, which stores up to 9 full-size SD cards as well as 9 Micro SD cards.

I recommend printing this if you have a large amount of SD cards to store. This is not great for cards which you are using constantly, as it will get tedious to remove individual cards. This is dense storage for those of us who have lots of these cards and adapters lying around.

Print settings are as usual for my Gridfinity items:

Layer height: .24 - .32
Top / Bottom Layers + Walls: 3 - 4
Infill: 10% - 20%

Use the lower values for cheaper / faster prints; use the higher values for weightier / higher quality items. You get the idea.

Gridfinity Dense 1x1 Full SD & Micro SD Storage

This item is for use with the #GridFinity system by Zach Freedman:

[https://www.youtube.com/watch?v=ra_9zU-mnl8](https://www.youtube.com/watch?v=ra_9zU-mnl8)

**UPDATE 4**
Added 3x5x2 and 3x5x1 as per request. Since I've been accused of being un-intellegent (yes hyphenated) in the comments I've resolved never to add a readme file to any of my models. You'll just have to remember where you downloaded them.

**UPDATE 3**

As per request, added 1x4x1, 1x4x2, 1x5,1 1x5x2.

**UPDATE 2**

More new sizes, as per request. Also added the source file, though I'm not sure anyone will understand my crude methods.

**2x3x1**
**2x3x2**

**2x4x1**
**2x4x2**

**2x5x1**
**2x5x2**


**UPDATE**

 A set of Gridfinity baskets with a hex mesh grid. Multiple sizes now include (WxDxH):

**1x1x1**
**1x2x1**
**1x3x1**

**1x1x2**
**1x2x2**
**1x3x2**

**2x2x1**
**2x2x2**



Contrary to Zach's instructions, I've been printing all my modules with a 0.8 nozzle, which seems to work just fine. The basket was printed with silver PLA at 75mm speed on an ender 3 pro with 0.8 nozzle and 0.32 layer height without support. The basket is slightly spongy and flexible. Remove any stringing with a heat gun or lighter.

#Gridfinity UPDATED 5/20/22! Hex Baskets

This item is for use with the #GridFinity system by Zach Freedman:

[https://www.youtube.com/watch?v=ra_9zU-mnl8](url)

 A 2 wide by 2 deep by 2 unit high basket with a hex mesh grid. I use this to store about 25 misc pens on a weighted base plate. 

Contrary to Zach's instructions, I've been printing all my modules with a 0.8 nozzle, which seems to work just fine. The basket was printed with silver PLA at 75mm speed on an ender 3 pro with 0.8 nozzle and 0.32 layer height without support. The basket is slightly spongy and flexible.

#Gridfinity 2x2x2 Hex Basket

**Update 04/06/22** (June not April ;-) )
Now that Fusion share link is working again you can now play with the source.
[https://a360.co/3x9cxGR](https://a360.co/3x9cxGR)

There are a couple of parameters you can play with:
_slotHeight_ - The total height of the box, set at the default 42mm.
_slotsHigh_ - A multiple for the slotHeight. This has a minimum of 1/3 (one third) of the slotHeight. Below that the label shelf goes wonky and you start losing area of the footprint.

**NOTE** The final 2 operations are extrusions. Supress/Unsupress these as you like to enable or disable the split and label shelf. They have been named to suit.

**Updated to V2**
Gridifnity compatible vase mode single cell boxes.

Yes, they stack
Yes, you can put stuff in 'em
Yes, you can have a spot for a label
Yes, you can have it split into 2 compartments.
Yes, they print wicked fast.
Yes, they are awesome in clear filament.

No, they're not compatible with magnets
No, they can't be more than 1 cell
No, you can't mess with the usual parameters on the stock gridfinity models, Standard size only.

Print with 2 or 3 bottom layers. 0.4 - 0.6 nozzle but limit the extrusion width to a max of 0.6. Don't go crazy on the layer height, the overhangs will bite (0.2-0.25 should be fine) Clear material looks great. PETG is pictured.

Thangs seems to cut off the filenames so they are:

- Vase mode single cell
- Vase mode single cell with label
- Vase mode split single cell
- Vase mode split single cell with label

#gridfinity Vase Mode Single Box

Vase Mode Single Cell.stl

Gridfinity

Categories

Popular

Personalize

Trending